manualshive.com logo in svg

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Поделиться
Скачать
SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 65

 

 

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc 

 

65/68 

plating electronic GmbH      -      Rheinstraße 4     -     D-79350 Sexau      -     Germany 

Tel.: +49 (0)7641 / 93500-0   - Fax.: +49  (0) 7641 / 93500-999   E-Mail:  [email protected]

 

 

 

23 

Checking calibration 

To check calibration of DC output current and voltage, some special tools are required: 

-  digital measuring instrument for voltage measurements with high-end measuring lines 

The measuring instrument needs to be calibrated. The accuracy of the measuring 
instrument must be better by a factor of 10 than the accuracy of the device to be 
calibrated. 

-  Ohmic load 60 Ohm 60 W (see below sketch) for the voltage measuring procedure 

-  Calibrated precision shunt that is capable for the maximum expected DC current of 

the rectifier unit (1 mOhm shunts are used in standard calibration applications of the 
DC power supply units). 

Generally 

It is not necessary to open the device! You just need to connect the measuring 
instrument, the shunt and the basic load to the DC output contacts of the rectifier unit. 
The rectifier unit should have the normal environmental temperature. 

It is recommended to use the original CAM LOCK connectors. 

23.1 

Voltage calibration 

Connect the basic load resistor 60 Ohm / 60 W to the DC output terminals. 

Connect the measuring lines of the digital measuring instrument to the DC output 
connectors of the rectifier unit. 

 

 

At the digital measuring instrument, select the voltage measuring range according to 
the maximum expected DC voltage output of the rectifier unit.

 

Turn on the main switch.  

Set the DC current to 1.50 A. Set the DC voltage to 1.00 V 

Press the ON key (you need to operate in manual mode, not in BUS control mode). 
Select Step “00”, normal operation.

 

Set the DC voltage to several levels and check the measured values on the digital 
measuring instrument. Compare with the values shown on the display of the rectifier unit. 

Start with 1 V, check in steps of 2 V until the nominal voltage is reached. 

Example: 60 A / 20 V 

set in % 

set value 

measured 

display 

5% 

1.00 V 

1.03 

1.00 

10% 

2.00 V 

2.01 

2.01 

15% 

3.00 V 

3.00 

3.00 

20% 

4.00 V 

4.03 

4.02 

. . . . and so on 

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды