manualshive.com logo in svg

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Поделиться
Скачать
SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 28

 

 

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc 

 

28/68 

plating electronic GmbH      -      Rheinstraße 4     -     D-79350 Sexau      -     Germany 

Tel.: +49 (0)7641 / 93500-0   - Fax.: +49  (0) 7641 / 93500-999   E-Mail:  [email protected]

 

 

 

16 

Potentiometer control and step function 

The digital potentiometers have several functions: 

- 

potentiometer control (value adjusting for DC output by turning the 
knobs) 

- 

reset value to zero (push knobs longer than 3 seconds) 

- 

digit selection (move digit marking from right to left by pushing the 
knobs) 

This applies for the voltage knob and the current knob. 

Generally, the rectifier DC output will just be enabled if the ON button on 
the control unit is actuated.

 

Generally 

After switching the main switch on, the control unit always starts in “OFF” 
status (DC output disabled). 

Apart from that, the unit will remember the last mode and step selection 
after restart. 

The loaded label number is shown on the display (top left). 

Press ON key to start. 

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды