SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 55

Страница: 55 / 68

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc

55/68

plating electronic GmbH - Rheinstraße 4 - D-79350 Sexau - Germany

Tel.: +49 (0)7641 / 93500-0 - Fax.: +49 (0) 7641 / 93500-999 E-Mail: [email protected]

Mode

Possible settings:

manually

auto

manually

The +/- key

is used to set the output polarity.

The manual mode is set by manufacturer when shipped.

The pole changer function generates an acoustic beep sound when the
pole changer will be switched to “reverse” mode!

Interval: 1 beep per second

auto

The pole changing is done according to the time settings
in this menu point.

Time settings

Time anodic:

for this time the polarity of the DC output is not
changed

Time cathodic:

for this time the polarity of the DC output is
changed

Alarm time:

If the polarity has changed to “cathodic” an acoustic alarm is given out.
With this menu point you can set the duration of this alarm. To disable
the acoustic pole changer indication set the value to zero.

Possible settings 0 - 10 seconds

For all time settings:

Use the keys “STORE / STEP RESET” to set the value

Short pressing on the key changes the value by one digit.

Constant pressing causes continuous change of the value.

Confirm the setting with ENTER.

Press CLR key to leave the menu.

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Результаты поиска

Содержание ASC TechnoPlate Power Pack 6030A20V

Отзывы:

Бренды по названию

Популярные бренды

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Результаты поиска

Содержание ASC TechnoPlate Power Pack 6030A20V

Отзывы:

Бренды по названию

Популярные бренды