manualshive.com logo in svg

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Поделиться
Скачать
SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 26

 

 

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc 

 

26/68 

plating electronic GmbH      -      Rheinstraße 4     -     D-79350 Sexau      -     Germany 

Tel.: +49 (0)7641 / 93500-0   - Fax.: +49  (0) 7641 / 93500-999   E-Mail:  [email protected]

 

 

 

13 

Function overview of the software 

The following control functions are implemented for the present SIFCO 
software: 

- 

Preset settings “PRESET” 

- 

Overload detection 

- 

Manual pole changer “+/-“ 

- 

Ampere counter Reset “A/H RESET” 

- 

STEP menu: configuration and labeling 

- 

STEP: buttons for switching between steps 

- 

STORE: Store button for storing new preset values 

- 

STEP RESET: delete the actual step 

- 

LABEL: Label setting for individual labeling of the presets 

- 

Digital potentiometers for fast and fine voltage and current control 

14 

Manual pole changer 

With DC output turned on, the pole changer generates an acoustic beep 
sound (interval) 

when it will be switched to “reverse” mode, and the 

indicator light will be red! 

Beep sound: 1 beep per second 

This configuration will be included in the factory settings and is 
predefined by plating electronic. 
 

 

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды