SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 11

Страница: 11 / 68

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc

11/68

plating electronic GmbH - Rheinstraße 4 - D-79350 Sexau - Germany

Tel.: +49 (0)7641 / 93500-0 - Fax.: +49 (0) 7641 / 93500-999 E-Mail: [email protected]

5.2

Switch mode technology

This device was designed as switch mode type DC power supply. The
advantages of the switch mode technology are:

very compact design

maximum regulation accuracy

very low ripple

high efficiency; optimized power factor (0.95, correlated to nominal
DC values)

5.3

Intended purpose

Device for industrial application

According to the norms

DIN EN 61000-3-12 (VDE 0838-12):2012-06

EN 61000-3-12:2011

this device is only to be used for industrial applications. Offering and
selling the device to the general public is not provided.

This device was designed to be used for selective electroplating
processes in plating systems only.

All other use must be clarified with the technical support of the
manufacturer. Otherwise, the installation or other connected devices
could be damaged.

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Результаты поиска

Содержание ASC TechnoPlate Power Pack 6030A20V

Отзывы:

Бренды по названию

Популярные бренды

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Результаты поиска

Содержание ASC TechnoPlate Power Pack 6030A20V

Отзывы:

Бренды по названию

Популярные бренды