manualshive.com logo in svg

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Поделиться
Скачать
SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 7

 

 

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc 

 

7/68 

plating electronic GmbH      -      Rheinstraße 4     -     D-79350 Sexau      -     Germany 

Tel.: +49 (0)7641 / 93500-0   - Fax.: +49  (0) 7641 / 93500-999   E-Mail:  [email protected]

 

 

 
This DC power supply was delivered after a thorough function- and 
safety-check. Only qualified staff shall connect the device and put it into 
operation. Service and maintenance is only to be performed by qualified 
personnel. 

Unauthorized modification or repairing is life endangering. Observe all 
instructions of the manufacturer; else, the warranty for DC power 
supplies and accessories will expire. 

Parts carrying a life-endangering voltage potential are installed inside the 
casing. These are marked with warning labels. 

Any manipulation of the electrical parts is life endangering and, by doing 
so, including improper operation, cancels the guarantee. 

This DC power supply was constructed in consideration of the threat 
analysis and the relevant safety regulations. Further, all relevant 
technical specifications are respected. Therefore, this technology is 
state-of-the-art and guarantees a maximum of safety and functionality. 

The safety and functionality can only be kept if the all relevant 
arrangements are done. 

The operator of the installation is responsible for the adherence of safety 
rules. 

The operator has to ensure that

 

- 

the DC power supply is only to be used for the application released 
by the manufacturer 

Active loads such as batteries or generators must never be 
connected to the DC generator (danger of destruction)! 

- 

the installation is only to be put into operation if it is in an accurate 
condition and all safety devices are checked regularly.  

- 

all requested individual protective equipment for operator and 
maintenance personnel is available and is be used. 

- 

The operating manual must be available at the operating place. The 
operating manual must be complete and in a good condition. 

- 

Mounting, repairing, electrical installation, adjusting and 
maintenance are only to be done by qualified personnel! 

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды