SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 10

Страница: 10 / 68

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc

10/68

plating electronic GmbH - Rheinstraße 4 - D-79350 Sexau - Germany

Tel.: +49 (0)7641 / 93500-0 - Fax.: +49 (0) 7641 / 93500-999 E-Mail: [email protected]

General description

The DC-power supply type

SIFCO ASC TechnoPlate Power Pack

a sophisticated switch mode type rectifier, designed for the selective
electroplating industry. It is designed as a desktop unit.

5.1

Two housing sizes

The control of the output parameters is done by keys and rotary buttons
in the front panel of the unit, or by RS485 BUS interface.

The electronic regulation guarantees correct output parameters during
the operation, even with variable loads at the DC output.

The pole changer can be programmed individually, according to your
application.

The pole changer can be operated in MANUAL or AUTO pole changer
mode.

The

preset counter

can be individually configured. The preset counter

can be used to switch the DC power supply off after a certain current
rate.

The

A/H

RESET

key is used to start the preset counter manually (or to

enable auto-start) if the plating process is running.

Over temperature protection

The device is temperature protected. If the interior temperature is
exceeding the limit the device decreases the output current
automatically and, after a cooling phase, increases it.

There is an auto-switch-off function in case of overheating.

Attention!

Auto-power-up after cooling down!

Do not run the power supply at higher environmental temperatures
than 40 °C and lower environmental temperatures than 5 °C!

Size 2:
15 A / 20 V and
30 A / 20 V,
control panel integrated

Size 1: air cooled by fans,
detachable control unit,
protective cover

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Результаты поиска

Содержание ASC TechnoPlate Power Pack 6030A20V

Отзывы:

Бренды по названию

Популярные бренды

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Результаты поиска

Содержание ASC TechnoPlate Power Pack 6030A20V

Отзывы:

Бренды по названию

Популярные бренды