manualshive.com logo in svg

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Поделиться
Скачать
SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 41

 

 

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc 

 

41/68 

plating electronic GmbH      -      Rheinstraße 4     -     D-79350 Sexau      -     Germany 

Tel.: +49 (0)7641 / 93500-0   - Fax.: +49  (0) 7641 / 93500-999   E-Mail:  [email protected]

 

 

 
If the voltage and current setting is finished: 

Press Ah PRESET key: 

Within 15 seconds, press 
STORE key to increase and 
STEP RESET key to 
decrease the Ah preset 
value on the left side of the 
decimal place. 

Press ENTER to confirm and move to the digits to the right of the decimal 
point. 

Press STORE key to increase 
and STEP RESET key to 
decrease the Ah preset value 
on the right side of the 
decimal point. 

Press ENTER to confirm and store the Ah preset value. 

Before you store the STEP preset, enter a STEP name as described 
above (see “LABEL key”). 

Store the STEP preset: 

Press and hold the STORE key for 3 seconds until you hear a short 
beep. The display says: “

STEP stored successfully!”

 

3 sec. 

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды