manualshive.com logo in svg

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Поделиться
Скачать
SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 47

 

 

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc 

 

47/68 

plating electronic GmbH      -      Rheinstraße 4     -     D-79350 Sexau      -     Germany 

Tel.: +49 (0)7641 / 93500-0   - Fax.: +49  (0) 7641 / 93500-999   E-Mail:  [email protected]

 

 

 

20.3 

Configuration of BUS interface 

If you are in the in the “Settings” menu, press the 
key located beside the 

RS485 BUS 

line. 

The display shows: 
 

 

The following menu points are available in this menu: 

- Mode: 

manual / Auto (manual = DEFAULT setting) 

- Baudrate: 

data transfer speed in auto mode 

- Address: 

RS485 BUS address of this device within 
the BUS line 

- Spec/Type: 

Protocol type for RS485 BUS 

Use the “STEP” keys to select the line 

Select “manually” or “auto” mode by using 
the “STORE / STEP RESET” keys. 

Confirm the setting with ENTER. 

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды