Siemens SIWAREX FTC Скачать руководство пользователя страница 97

Страница: 97 / 149

EIGHING

UNCTIONS AND

ARAMETERS

5.24 DR 47 Requested Log

The log data is prepared in DR 47.

Name

Type

Address

Default

Range of Values / Meaning

Reference

MMC-ID

BYTE[5] DBB000

1 byte manufacturer's ID + 4 bytes serial
number; with log output to RS232 interface
always 0

Reserve 1

BYTE DBB005

Reserve

Reserve 2

WORD DBB006

0 Reserve

Log ID

DINT DBD008

ID for stored log text

Log data 1

STRING[40]

DBB012

STRING[40] = 0H

Log text Part 1

Log data 2

STRING[40]

DBB054

STRING[40] = 0H

Log text Part 2

Log data 3

STRING[40]

DBB096

STRING[40] = 0H

Log text Part 3

Log data 4

STRING[40]

DBB0138

STRING[40] = 0H

Log text Part 4

180

Table 5-25

Allocation of DR 47

5.24.1 DR 47 - MMC-ID

Identification of the MMC card.

5.24.2 DR 47 - Log ID

The log ID is a unique log number that can be used to identify the log. The number
is incremented with every logging procedure.

5.24.3 DR 47 - Log Data

The log data consists of 4 strings.

5.25 DR 120/121 Trace - Data Logging

The trace function is used for logging measurement values and current states of
the scale in RAM memory of the SIWAREX FTC or in the MMC card.

When logging to RAM, SIWATOOL FTC reads the trace elements with data record
120 and when logging to the MMC it is done through data record 121.

The recording is started with the instruction "Start the recording"

and can be

ended with instruction "End current recording"

By defining parameters in data record DR 7

MMC Parameter

the trace function

can be defined. The data record cannot be read through the SIMATIC CPU.

Name

Type

Length

bytes

Range of Values / Meaning

Reference

Timestamp1 DATE&TIME

Conti- Status flag

DINT

Status bit

NAWI status flags

DINT

Status bit

Unfiltered raw value

DINT

Unfiltered digit value from ADC

SIWAREX FTC

5-85

Содержание SIWAREX FTC






















































































































































Результаты поиска

Содержание SIWAREX FTC

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIWAREX FTC, Руководство по эксплуатации устройства

Результаты поиска

Содержание SIWAREX FTC

Отзывы:

Бренды по названию

Популярные бренды