manualshive.com logo in svg

Siemens SIWAREX FTC, Руководство по эксплуатации устройства

Поделиться
Скачать
Siemens SIWAREX FTC Скачать руководство пользователя страница 62

 

5.4.5 

DR 4 - Basis Weight for Monitoring the Empty Range 

The limit value for the monitoring of the empty range can be defined in relation to 
the gross weight or the net weight of the scale.  

5.4.6 

DR 4 - Empty Range 

The value for the empty range is a limit value, that when exceeded indicates the 
"empty" status to the SIWAREX FTC which gives this out as status information. 

In operating mode Loss-in-weight scale, emptying in automatic mode is ended if 
the value drops below the limit value. 

5.4.7 

DR 4 - Switch-on Weight Limit Value 1 

Switch-on and shut-off weights can be defined separately for a limit value. In this 
way, a minimum value monitor and a maximum value monitor can be realized by 
hysteresis. A maximum value monitor is realized with the following specification: 

Switch on value > Switch off value 

A minimum value monitor is realized with the following specification: 

Switch on value < Switch off value 

The following image shows the functionality of limit values 1, 2, 3 

 

FIGURE 5-6 

Defining limit value parameter 

5.4.8 

DR 4 - Cut-off Weight Limit Value 1 

See: Switch On Weight, Limit Value 1 

5.4.9 

DR 4 - Switch-on Weight Limit Value 2 

See: Switch On Weight, Limit Value 1 

5-50

 

SIWAREX FTC

 

Содержание SIWAREX FTC






















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды