manualshive.com logo in svg

Siemens SIWAREX FTC, Руководство по эксплуатации устройства

Поделиться
Скачать
Siemens SIWAREX FTC Скачать руководство пользователя страница 130

 

9 Commissioning with a PC – SIWATOOL FTC_B 

9.1  General 

 
The scale can be put into operation using the SIWATOOL FTC_B independent of 
the commissioning of the SIMATIC automation system. 
 
This program is included in the configuration package supplied.  
The program (catalogue SIWATOOL_FTC) must be installed in the first step. Less 
than 30 MB is required on the hard drive. 
 

9.2  Windows and Functions in SIWATOOL FTC_B 

The program window is constructed so that navigating through the parameter 
definition areas of the SIWAREX FTC is made easier. In the left-hand portion, the 
overview of the parameters is shown as a tree-structure. The parameter grouping 
corresponds with the various activities which can happen during the project 
planning, commissioning, tests and for service cases. 
A data record in SIWAREX FTC belongs to every branch of the tree structure. 
Several parameters are combined in one data record. In the right-hand window, the 
parameters in a data record can be edited in index card format. 
The first card in a box is set up as an information sheet. The user is shown which 
tasks can be processed with the parameters of the selected data record in this 
information sheet. For sending, receiving and transferring, the entire data record is 
always handled, not just an index card. 
 

9.3  Offline Configuration 

All scale parameters can be processed and stored without the SIWAREX FTC. 
This reduces the commissioning time. 
The parameters for more than one scale can be prepared in the office and only 
have to be transferred to the SIWAREX FTC when starting the operation on-site. 
Data from one scale that is currently in operation can be read and used in the 
commissioning of another scale. 

9.4  Online Operation 

To switch to online operation, the PC must be connected to the SIWAREX FTC 
with the SIWATOOL cable (see 

Accessories

). The COM interface can be set up in 

the communication menu. 
All parameters can be changed in online operation. A message window shows the 
current content of the message buffer in SIWAREX FTC. The current process 
values can be observed in the various windows. For testing, all commands can be 
sent to the SIWAREX FTC. 
All data can be read out and stored as a file or printed for archiving purposes. 

9-118

 

SIWAREX FTC

 

Содержание SIWAREX FTC






















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды