manualshive.com logo in svg

Siemens SIWAREX FTC, Руководство по эксплуатации устройства

Поделиться
Скачать
Siemens SIWAREX FTC Скачать руководство пользователя страница 63

W

EIGHING 

F

UNCTIONS AND 

P

ARAMETERS

 

5.4.10  DR 4 - Cut-off Weight Limit Value 2 

See: Switch On Weight, Limit Value 1 

5.4.11  DR 4 - Switch-on Weight Limit Value 3 

The switch-on and cut-off weight can be defined separately for the limit value. 
With limit value 3, only the maximum weight monitor can be used. The basis weight 
for the limit value 3 is always the gross weight. 

5.4.12  DR 4 - Cut-off Weight Limit Value 3 

When the limit value is undercut, the status information "limit value 3) is reset. 

 

5.5  DR 5 Belt Scale Parameter  

The basis parameter for belt scale defines other features of a scale which are 
responsible for the behavior in the belt scale operating mode. The parameter must 
be checked and changed in some cases. 

Procedure: 

o

  Check all parameters and change if necessary. 

o

  Send the DR 5 to the scale 

 

Name 

Type 

Address 

Default 

Range of Values / Meaning 

Reference 

Nominal speed 

 

REAL DBD000 

0 
 

Nominal speed of the belt in LU/s (Length 
units per second) 

5.5.1 

Time basis for belt 
speed 
 

TIME 

DBD004 

0 

Time basis for measuring the belt speed  by 
impulse counter input (msec) 

5.5.2 

Pulse constant 
 

REAL 

DBD008 

0 

Pulse constant of the speed sensor 

5.5.3 

Constant belt speed 
 

REAL 

DBD012 

2000 

Constant speed if no speed sensor is 
connected. 
0 – for connecting the speed sensor. 

5.5.4 

Minimum belt speed 

INT 

DBW016 

800 

Limit value for minimum belt speed in % of 
the nominal speed. 
800 corresponds with 80.0 % 

5.5.5 

Maximum belt speed 

INT 

DBW018 

1020 

Limit value for maximum belt speed in % of 
the nominal speed. 
1020 corresponds with 102.0 % 

5.5.6 

Reaction time for belt 
monitor 
At start 

TIME DBD020 

 

Reaction 

time 

for belt monitoring and belt 

cycle error message at belt start 

5.5.7 

Reaction time for belt 
monitor 
During operation 

TIME DBD024 

 

Reaction 

time 

for belt monitoring and belt 

cycle error message during belt operation 

5.5.8 

Reserve_5_28 REAL 

DBD028 

 

Reserved 

 

Nominal flow-rate 
 

REAL 

DBB032 

 

Nominal flow-rate in weight units / s 
 

5.5.9 

Effective belt length 
 

REAL 

DBB036 

 

Effective belt length in length units LU 
 

5.5.10 

Correction factor for 
flow-rate 
 

REAL 

DBB040 

 

Correction factor for the flow rate 

5.5.11 

Minimum flow-rate 

INT

 

DBD044 

 

Limit value for minimum flow-rate in % of the 
nominal flow-rate 

5.5.12 

Maximum flow-rate 

INT

 

DBD046 

 

Limit value for maximum flow-rate in % of the 
nominal flow-rate 

5.5.13 

SIWAREX FTC 

5-51 

Содержание SIWAREX FTC






















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды