manualshive.com logo in svg

Siemens SIWAREX FTC, Руководство по эксплуатации устройства

Поделиться
Скачать
Siemens SIWAREX FTC Скачать руководство пользователя страница 114

 

Error 

No. 

Data and operating 
errors 
- Meaning 

Explanation 

56 

Log text too long 

The log text with filled in parameters is too long or the end 
character (EOT) is missing. Change the log text. 
Ensure that in place of the corresponding print field code, the 
respective number of characters for the field is set. The overall 
length of the text filled with values may not exceed 160 
characters (incl. printer control characters but without the 
termination EOT). 

57 

Log text contains 
fields that are not 
permitted 

Log text contains fields that are not permitted Change the log 
text. 

58 

Log text contains 
angle-brackets 

Log text contains angle-brackets Remove the angle-brackets 
from the log text. 

62 

Logging not possible 
since the weight lies 
outside of the 
weighing range 

Logs can only be output within the weighing range in verifiable 
operation (code OIML in DR 3). 

63 

Logging output not 
possible since the 
SIWATOOL FTC 
driver is active 

The log can not be output because the SIWATOOL FTC_B is 
active on the interface. Disconnect the PC and connect the 
printer. 

64 

Logging output not 
possible since the 
printer is not ready  

The log cannot be printed since the printer is not ready. Check 
the printer. 

65 

Logging output not 
possible since a print 
job is still running 

The log cannot be printed since another print job is still 
running. Wait until the current print job is complete. 

66 

Logging not possible 
since the MMC is full 

Logging is not possible since the MMC is full. Switch MMCs. 

67 Logging 

task 

cannot 

be executed, since 
MMC is defective or 
non-existent 

Logging is not possible since the MMC is defective. Switch 
MMCs. 

68 

Log output not 
possible since no data 
is available.  

Repeating the last log print-out is not possible since there has 
been no previous print-out or the saved data is defective. 

70 

Logging output not 
possible since the log 
ID is not in the print 
text 

Log output is not possible since the content of the text does not 
contain the log ID. Define the log ID in the text. This entry is 
necessary if the verifiable weight is contained in the log text in 
verifiable operation ((Technical regulation code OIML in DR 3). 

76 Value 

range 

Adjustment digits 
exceeded 

The definition for the adjustment digits in DR  3 is too large. 
Enter a smaller value. The highest permitted value is 
16 777 215. 

77 Regulation 

code 

not 

permitted 

The regulation code is incorrect. Enter the proper code. 
The permitted entries are ---- or OIML. 

78 

Zero setting range > 
4% or zero setting 
range exceeded 

The zero definition range or zero setting range is too large. 
This is the case if you have defined a zero setting range of > 
4% of the maximum weighing range, or > 20% of the zero 
setting range in DR 3 in verifiable operation (technical 
regulation code OIML in DR 3). The sum of the negative and 
positive values apply in this instance. Reduce the zero 
definition range or zero setting range.  

7-102

 

SIWAREX FTC

 

Содержание SIWAREX FTC






















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды