manualshive.com logo in svg

Siemens SIWAREX FTC, Руководство по эксплуатации устройства

Поделиться
Скачать
Siemens SIWAREX FTC Скачать руководство пользователя страница 105

C

OMMANDS

 

Code  Command explanation 

Comment 

105 

Switch off dosing (belt scale) 

Deactivate discharge organ 
 

 

106 

Switch belt on, switch on totalizing 

The belt scale sends a signal for dosing (The belt 
control bit is set in the CONTI status).  
Totalizing is activated. 
The loading quantity (DR 21) must be larger than the 
lag.  
The content of distribution memory 1 must be less 
than the loading quantity - lag. 
The distribution memory is not deleted at the start. 
 

 

107 

Switch the belt on, switch totalizing on, switch 
dosing on

 

Material loading is started corresponding with the 
total quantity definition, totalizing is switched on and 
belt control is switched on. 
The content of distribution memory 1 must be less 
than the loading quantity - lag. If necessary, delete 
the content of the distribution memory 1 in advance. 
The loading quantity (DR 21) must be larger than the 
lag. 
 

 

110 

Delete all distribution memory 

Deletes all 8 distribution memory locations. 
 

 

111 

Log and delete distribution memory 1  

Deletes verifiable distribution memory 1 

This automatically includes a logging procedure. In 
this case, the text 1 (DR 40) is used- The deletion is 
only performed if the total 1 is contained in the log 
text.

 

 

 

112 

Delete distribution memory 1 

Deletes distribution memory 1. 
 

 

113 

Log and delete distribution memory 2 

Deletes distribution memory 2. 

This automatically includes a logging procedure. 
Text 1 (DR 40) is used here. The deletion is only 
executed if total 2 is contained in the log text.

 

 

 

114 

Delete distribution memory 2 

Deletes distribution memory 2. 
 

 

115 

Log and delete distribution memory 3  

Deletes distribution memory 3. 

This automatically includes a logging procedure. 
Text 1 (DR 40) is used here. The deletion is only 
executed if total 3 is contained in the log text.

 

 

 

SIWAREX FTC 

6-93 

Содержание SIWAREX FTC






















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды