Siemens SIWAREX FTC Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 149

Siemens SIWAREX FTC Скачать руководство пользователя страница 88

Bit No.

Name

Range of Values / Meaning

Reference

26

Status change

Status change running. The information is set with the
following events:
- Start-up in volumetric operation
- Setpoint change in volumetric operation
- Switch to grav. operation. For the time of the monitoring
delay (DR 12)
- defined switch to volumetr. operation upon flow rate fault

27 Reserved

Reserved

28

Dosing active

Switch on material discharge organ

29

Loading active

Loading (belt scale) is activated.

30

Loading complete

Loading (belt scale) is complete.

31 Reserved

Reserved

Table 5-15

DR 30 - Conti-Status flags

5.15.3 DR 30 - Gross Process Value

The current gross weight value. Dimension: Weight Unit [WU].

5.15.4 DR 30 - Net Process Value

The current net weight value. Dimension: Weight Unit [WU].

5.15.5 DR 30 - Tare Process Value

The current tare weight value. Dimension: Weight Unit [WU].

5.15.6 DR 30 - G/N Weight

The momentary weight value which will be used for the main display. Dimension:
Weight Unit [WU].

5.15.7 DR 30 - G/N Weight_x10

The momentary weight value in increased resolution which will be used for the
main display. Dimension: Weight Unit [WU].

5.15.8 DR 30 - Tare

The current weight value tare (numeral step from DR 3). Dimension: Weight Unit [WU].

5.15.9 DR 30 – Belt Speed

The current belt speed defined in length units (e.g. m) per second.

5.15.10 DR 30 – Belt Speed in % of the Nominal Speed

The current belt speed in % of the predefined nominal speed.

5.15.11 DR 30 – Belt Loading in % of the Nominal Load

The current belt load is output as the relationship of the current belt load to the
nominal belt load.

5-76

SIWAREX FTC

«
...
86
87
88
89
90
...
»

Содержание SIWAREX FTC






















































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды