manualshive.com logo in svg

Siemens SIWAREX FTC, Руководство по эксплуатации устройства

Поделиться
Скачать
Siemens SIWAREX FTC Скачать руководство пользователя страница 56

 

log or zero setting was not possible after this time has elapsed then the 
corresponding technology message generated. 

5.2.25  DR 3 - Maximum Negative Weight for Zero Setting upon Switch On  

Zero setting means that an automatic zero setting is performed for the scale when 
the supply voltage is switched on.  

If zero setting upon switching on the supply voltage has been activated, then the 
definition will limit the affect of the function. The reference point for the 
effectiveness of the limitation is not the current weight, it is the weight that was 
displayed by the scale without a previous zero setting. In operating modes "Belt 
scale" and "Loss-in-weight scale", this function is not effective. 

5.2.26  DR 3 - Maximum Positive Weight for Zero Setting upon Switch On 

Zero setting means that an automatic zero setting is performed for the scale when 
the supply voltage is switched on. 

If zero setting upon switching on the supply voltage has been activated, then the 
definition will limit the affect of the function. The reference point for the 
effectiveness of the limitation is not the current weight, it is the weight that was 
displayed by the scale without a previous zero setting. In operating modes "Belt 
scale" and "Loss-in-weight scale", this function is not effective. 

5.2.27  DR 3 - Maximum Negative Weight for Zero Setting  

The current gross weight of the scale is defined as zero for zero setting. 

For zero setting, the specification can be used to limit the effect of the function. 
The reference point for the affect of the limitation is not the current gross weight. 
It is the weight that the scale would show without a previous zero setting. 

For scales in calibrating operation, the limit between the negative and positive 
weight for zero setting is 4% of the maximum weighing range. 

5.2.28  DR 3 - Maximum Positive Weight for Zero Setting  

For zero setting, the specification can be used to limit the effect of the function. 
The reference point for the effectiveness of the limitation is not the current weight, 
it is the weight that was displayed by the scale without a previous zero setting. 

For scales in calibrating operation, the limit between the negative and positive 
weight for zero setting is 4% of the maximum weighing range. 

5.2.29  DR 3 - Tare max. Weight T- 

SIWAREX FTC accepts every weight value which is less than %-record of the 
maximum weighing range with multi-range scales or weighing range 1 with a multi-
resolution scale. 

On scales in verifiable application, the value is limited to 100% of the maximum 
weighing range. 

5.2.30  DR 3 – Operating Mode 

This parameter can be used to select the suitable weighing program. One of these 
weighing operating modes applies depending on the task description. 

5-44

 

SIWAREX FTC

 

Содержание SIWAREX FTC






















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды