Siemens SIPROTEC 5 6MU85 Скачать руководство пользователя | Manualshive

Страница: 6 / 107

background image

NOTICE

NOTICE means that property damage can result if the measures specified are not taken.

²

Comply with all instructions, in order to avoid property damage.

i

i

NOTE

Important information about the product, product handling or a certain section of the documentation
which must be given attention.

Qualified Electrical Engineering Personnel

Only qualified electrical engineering personnel may commission and operate the equipment (module, device)
described in this document. Qualified electrical engineering personnel in the sense of this manual are people
who can demonstrate technical qualifications as electrical technicians. These persons may commission,
isolate, ground and label devices, systems and circuits according to the standards of safety engineering.

Proper Use

The equipment (device, module) may be used only for such applications as set out in the catalogs and the
technical description, and only in combination with third-party equipment recommended and approved by
Siemens.
Problem-free and safe operation of the product depends on the following:

•

Proper transport

•

Proper storage, setup and installation

•

Proper operation and maintenance

When electrical equipment is operated, hazardous voltages are inevitably present in certain parts. If proper
action is not taken, death, severe injury or property damage can result:

•

The equipment must be grounded at the grounding terminal before any connections are made.

•

All circuit components connected to the power supply may be subject to dangerous voltage.

•

Hazardous voltages may be present in equipment even after the supply voltage has been disconnected
(capacitors can still be charged).

•

Operation of equipment with exposed current-transformer circuits is prohibited. Before disconnecting the
equipment, ensure that the current-transformer circuits are short-circuited.

•

The limiting values stated in the document must not be exceeded. This must also be considered during
testing and commissioning.

Used Symbols on Device

No.

Symbol

Description

1

Direct current, IEC 60417, 5031

2

Alternating current, IEC 60417, 5032

3

Direct and alternating current, IEC 60417, 5033

4

Earth (ground) terminal, IEC 60417, 5017

5

Protective conductor terminal, IEC 60417, 5019

Preface

6

SIPROTEC 5, Merging Unit 6MU85, Manual

C53000-G5040-C074-1, Edition 01.2020

«
...
4
5
6
7
8
...
»

Содержание SIPROTEC 5 6MU85












































































































Отзывы:

Нет отзывов

Похожие инструкции для SIPROTEC 5 6MU85

Бренд: Navman Страницы: 17

Бренд: parr Страницы: 20

Бренд: Landoll Страницы: 71

Бренд: York Fitness Страницы: 4

Бренд: W&H Страницы: 23

Бренд: Bartscher Страницы: 24

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Quivogne Страницы: 13

Бренд: RAPID REBOOT Страницы: 18

Бренд: MacDon Страницы: 170

Бренд: MacDon Страницы: 108

Бренд: MacDon Страницы: 108

Бренд: MacDon Страницы: 51

Бренд: MacDon Страницы: 104

Бренд: MacDon Страницы: 240

QUANTOFIX Relax

Бренд: Macherey-Nagel Страницы: 192

Бренд: MacDon Страницы: 182

Бренд: MacDon Страницы: 192

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды