Siemens SiPass integrated Скачать руководство пользователя страница 50

Страница: 50 / 66

Controller Event Tasks
Commands

50 | 66

A6V11144326

Type

Command

Description

Return to Time Schedule

Control

Returns the Target point to normal Time

Schedule control.

Cancel Permanent

Action

Any current Permanent Command or Event

Task, or Access/Internal Action operating

on the target will be cancelled. The next

Control State in the Control State Queue

will take effect.

Reset Reader Tamper

Resets the reader tamper for the specified

reader. Only available for the Siemens

reader range.

Reader Buzzer on

Turns the buzzer for the specified reader

ON. Only available for the Siemens reader

range.

Reader Buzzer Off

Turns the buzzer for the specified reader

OFF. Only available for the Siemens reader

range.

Block Door

Blocks the door for the associated reader.

Unblock Door

Unblocks the door for the specified reader,

the reader returns to its programmed mode

of operation.

Set

mode “No Dual

Custody”

Disables Dual Custody for the access

point.

Set mode “Standard Dual

Custody”

Set the access point to Standard Dual

Custody Mode.

Set mode “Supervisory

Dual Custody”

Set the access point to Supervisory Dual

Custody Mode.

Restore Dual Custody

Config Mode

Restores Dual Custody to the configured

mode.

Report Dual Custody

Config Mode

Reports the configured Dual Custody

mode.

Set “No Additional

Access”

Set the additional access for the selected

access point to No Additional Access.

Set “Daily Code”

additional access mode

Set the additional access for the selected

access point to Daily Code.

Set “PIN as Card”

additional access mode

Set the additional access for the selected

access point to PIN as Card.

Restore additional

access mode

Returns the access point to the normal

additional access operation mode defined

in the Components screen.

Unlock Door, Override

Door Interlocking

Unlocks the door and ignores any Door

Interlocking configuration.

Allow Access, Override

Door Interlocking

Allows access and ignores any Door

Interlocking configuration.

Intrusion Control

–

Enable

Enable Intrusion Control on the selected

access point.

Intrusion Control

–

Disable

Disable Intrusion Control on the selected

access point.

Intrusion Control

–

Restore Config

Restore Intrusion Control to whatever is

configured.

Содержание SiPass integrated



































































Результаты поиска

Содержание SiPass integrated

Отзывы:

Siemens SiPass integrated, Справочное руководство, Страница: 50 / 66

Результаты поиска

Содержание SiPass integrated

Отзывы: