Siemens SiPass integrated Скачать руководство пользователя страница 13

Страница: 13 / 66

Alarm Class

A6V11144326

13 | 66

Type

Status

Description

Intrusion Control Enabled Intrusion Control has been enabled at the

reader.

Duress

A duress alarm has been entered at an

access point.

Soft Anti-passback mode A cardholder has failed to use their card

when leaving an area with soft anti-passback

and has tried to re-enter the same area. The

cardholder will be allowed access.

Hard Anti-passback mode A cardholder has failed to use their card

when leaving an area with hard anti-

passback and has tried to re-enter the same

area. The cardholder will be denied access.

A card read at a disabled

readhead

A card was read at a disabled readhead.

(Disabled readhead

–

refers to a card reader

that has been sent a manual Disable

command).

Group error

A card, from a group (of cards) that has been

disabled, was used at a reader or is invalid

for the reader where it was used.

Alarm void card was read A void card was read at an access point.

An invalid facility card was

read

An invalid Facility Code on a card was read

at an access point. (Each site has a site-

specific Facility Code).

Card number limit

The maximum number of cards supported by

the hardware (processor) has been reached.

An invalid PIN number

An invalid PIN (Personal Identification

Number) was entered at an access point.

Bad daily code

An invalid Daily Code was entered at a

keypad that requires a Daily Code to be

entered.

Independent service

The elevator has been placed on

independent service. (The elevator operates

independ-ently of all other elevators, usually

controlled from inside the elevator itself).
Typically initiated when being repaired.

Elevator Alarm

The emergency or alarm button within the

elevator has been activated.

Tamper active on reader

The tamper input on a reader interface

module is active.

Reader offline

A reader has gone offline.

Checksum error on reader Not supported.

Access not granted on

reader

Access was denied at an access point.

Door (Latch) unlocked

The door latch has been unsecured.

Hard Anti-Pass back Error A cardholder has failed to use their card

when leaving an area with soft anti-passback

and has tried to re-enter the same area. The

cardholder will be allowed access.

Содержание SiPass integrated



































































Результаты поиска

Содержание SiPass integrated

Отзывы:

Siemens SiPass integrated, Справочное руководство, Страница: 13 / 66

Результаты поиска

Содержание SiPass integrated

Отзывы: