Siemens SiPass integrated Скачать руководство пользователя страница 24

Страница: 24 / 66

Manual Override

24 | 66

A6V11144326

Manual Override

Manual Commands can be used to manually control specific points, areas,

elevators and units at your site. The following table lists the commands that can be

used to control each type and a brief description of the action that will be

performed.

Type

Command

Description

Access

Allow Access

The door will unlock, remain unlocked for the

defined period of time and then relock, as per a

normal valid card badge.

Block Door

The door will remain blocked, unable to be opened.

Cancel Permanent

Action

Any current Permanent Command or Event Task,

or Access/Internal Action operating on the point will

be cancelled. The next Control State in the Control

State Queue will take effect.

Intrusion Control -

Disable

Disable Intrusion Control on the selected access

point.

Intrusion Control

–

Enable

Enable Intrusion Control on the selected access

point.

Intrusion Control

–

Restore Config

Restore Intrusion Control to whatever is configured.

Lock Door

The door latch will be locked until the next unlock

command is received.
The Duration can be set to:

●

Until time schedule change

●

Permanents

Reader Buzzer Off

The Reader buzzer is turned off. Only applies to the

Siemens reader range.

Reader Buzzer On

Reader buzzer is turned on. Only applies to the

Siemens reader range.

Reset Reader

Tamper

Resets the reader tamper input. Only applies to the

Siemens reader range.

Restore Access

Mode

Returns the access point to the normal access

operation mode defined in the Components screen.

Restore additional

access mode

Returns the access point to the normal additional

access operation mode defined in the Components

screen.

Restore Dual

Custody Config Mode

Restores the Dual Custody mode to what is

configured.

Return to Time

Schedule Control

The door latch will return to normal Time Schedule

control.

Set “Daily Code“

additional access

mode

Set the additional access for the selected access

point to Daily Code.

Set “No Additional

Access“

Set the additional access for the selected access

point to No Additional Access.

Set “PIN as Card”

additional access

mode

Set the additional access for the selected access

point to PIN as Card.

Содержание SiPass integrated



































































Результаты поиска

Содержание SiPass integrated

Отзывы:

Siemens SiPass integrated, Справочное руководство, Страница: 24 / 66

Результаты поиска

Содержание SiPass integrated

Отзывы: