Siemens SiPass integrated Скачать руководство пользователя страница 12

Страница: 12 / 66

Alarm Class

12 | 66

A6V11144326

Alarm Class

This section lists all of the possible states and their descriptions for each Alarm

Type in the

Alarm Class

dialog.

When creating an alarm class, you can define alarm states. For example, if you

were to create an alarm class for output points (in particular, doors with locks), you

could create two states for that class. The first state would be a restore (normal)

state when the door is locked and the second state would be an alarm state when

the door is unlocked. The event that triggers the state (door locked or unlocked) is

known as the status.

Type

Status

Description

Access

Daily code

The correct Daily Code was entered at a

keypad.

Low battery detected

A card has been used that has a low HFPU

battery and needs to be replaced, as soon

as possible.

Good access with time

stamp

A valid card was read at a card reader.

Access granted to Anti-

Passback Area

A cardholder has successfully entered an

Anti-Passback area with a valid card.

Card activates APB area

either ON

A card was used to secure an area.

Card activates APB area

either OFF

A card was used to unsecure an area.

Card activates floor

A card was used at a card reader to secure a

floor.

Card did not activate a

floor

A card was used, unsuccessfully, at a card

reader to secure a floor.

Door Time Schedule

Active

A door has reverted to normal Time

Schedule control after being manipulated by

a manual command or Event Task.

Door Free

The door latch is open and the door frame

monitor is disabled.

Door Secured

The door latch is secured and the door frame

monitor is enabled.

Tamper inactive on reader The tamper input on a reader interface

module is inactive.

Reader online

A reader has come online.

Reader timeout

A reader has timed out after a card was

badged and PIN entry was expected.

Badge collision on reader Not supported.

Access granted on reader Access has been granted at an access point.

Door (Latch) locked

The door latch is secured.

No Additional Access

Mode Set

The reader has been set to No Additional

Access mode.

PIN as Card Mode Set

The reader has been set to PIN as Card

mode.

Daily Code mode set

The reader has been set to Daily Code

mode.

Содержание SiPass integrated



































































Результаты поиска

Содержание SiPass integrated

Отзывы:

Siemens SiPass integrated, Справочное руководство, Страница: 12 / 66

Результаты поиска

Содержание SiPass integrated

Отзывы: