Siemens SiPass integrated Скачать руководство пользователя страница 26

Страница: 26 / 66

Manual Override

26 | 66

A6V11144326

Type

Command

Description

Set state Alarm

Set the input to state Alarm. This is only applicable

for Sintony input points of type “Serial Comms

Input”

Set state Normal

Set the input to state Normal. This is only

applicable for Sintony input points of type “Serial

Comms Input”

Unsecure (Disable)

Disables the input, if it is currently enabled, until the

next change in Time Schedule.

Output

Allow Access

Allows access at an output point. (Operates in the

same way as if a cardholder used their card to gain

valid access at the same point). The output point

will only be activated for the latch time.

Cancel Permanent

Action

Any current Permanent Command or Event Task,

or Access/Internal Action operating on the point will

be cancelled. The next Control State in the Control

State Queue will take effect.

Fast Pulse

The output point will activate in “fast pulse” mode.

Return to Time

Schedule Control

The output will return to normal Time Schedule

control.

Secure (Lock)

Locks the output (temporarily), if the output is

currently unlocked. The Duration can be set to :
- Until Time Schedule Change
- Permanent
Duration time can be specified in the HH:MM:SS

format.

Single Pulse

The output will activate a single pulse.

Slow Pulse

The output will activate in “slow pulse” mode.

Toggle Point

The state of the output will be toggled to the

reverse state.

Unsecure (Unlock)

Unlocks the output (temporarily), if the output is

currently locked, until the next change in Time

Schedule.

APB Area
(Anti-

Passback

Area)

Forgive All cards

Forgives all cardholders currently in the area.

Forgive Card

Forgives the specified cardholder.

Override Mode

Overrides the selected area with a specific mode.

Reset Count

Allows the count for an Anti-Passback area to be

reset to zero.

Restore Mode

Restores the configured Anti-Passback mode.

Add Card

Adds a card to an Anti-Passback area.

Remove Card

Removes a card from an Anti-Passback area.

Intrusion

Arm

Arms the selected intrusion area.

Clear Intrusion

Alarms

Clears all alarms in memory for the selected area or

specified room.

Disarm

Disarms the selected intrusion area.

Isolate Point

Manually isolates a point from an intrusion area,

excluding that point from a seal check when the

area is armed.

Содержание SiPass integrated



































































Результаты поиска

Содержание SiPass integrated

Отзывы:

Siemens SiPass integrated, Справочное руководство, Страница: 26 / 66

Результаты поиска

Содержание SiPass integrated

Отзывы: