Siemens SINAUT MD720-3 Скачать руководство пользователя страница 68

Страница: 68 / 76

Service functions

SINAUT MD720-3

C79000-G8976-C211

Setup the Local Service Connection

When the modem driver and the network connection are installed and the SINAUT
MD720-3 is connected to the COM-Port of the PC, the service connection can be
established. Activate the service mode and continue as follows:

1. Open

the

Start

Menu.

2. Select the new connection (e.g.

Service-MD720)

in the menu

Connect to.

3. Enter the user name (default: service) and the password (default: service) and

click

Dial.

4. The connection will be established. After the connection is established an Icon

appears in the Windows taskbar.

5. In

the

Start

Menu click

All Programs

Accessories

Command Prompt

6. Enter the following command line: C:\WINDOWS>ftp 192.168.0.8

Press Enter.

7. You will be asked for a User name (default: service) and a password (default:

service). Enter both and observe capital or small characters.

8. If the connection is established successfully the message „230 User logged in“

appears and the prompt changes to Ftp>.

Содержание SINAUT MD720-3













































































Результаты поиска

Содержание SINAUT MD720-3

Отзывы:

Siemens SINAUT MD720-3, Системное руководство, Страница: 68 / 76

Результаты поиска

Содержание SINAUT MD720-3

Отзывы: