Siemens SINAUT MD720-3 Скачать руководство пользователя страница 58

Страница: 58 / 76

SINAUT MD720-3 in OPC Mode

SINAUT MD720-3

C79000-G8976-C211

5.1

OPC Mode activation

Terminal mode is factory default setting

The SINAUT MD720-3 supports two fundamental operating modes:

●

Terminal

mode

●

OPC

Mode.

The SINAUT MD720-3 will be delivered by the factory with activated Terminal
Mode.

Automatic activation by the PLC

Operating the SINAUT MD720-3 in OPC Mode combined with S7-200 devices, the
OPC Mode will be activated by the program building blocks automatically during
the initialization.

Manual activation

If in exceptional cases a manual activation of the OPC Mode is necessary, you will
find instructions in chapter 6.1

Switching between Terminal mode and OPC Mode

5.2

Operating requirements in OPC Mode: GPRS subscriber
contract

To use the SINAUT MD720-3 in OPC Mode it is required:

•

SIM card of a GSM network operator with activated GPRS,

•

SIM card of a GSM network operator including CSD data service 9600 Bit/s
and an extra telephone number for data calls (to make Teleservice),

Availability of a GSM network

Содержание SINAUT MD720-3













































































Результаты поиска

Содержание SINAUT MD720-3

Отзывы:

Siemens SINAUT MD720-3, Системное руководство, Страница: 58 / 76

Результаты поиска

Содержание SINAUT MD720-3

Отзывы: