Siemens SINAUT MD720-3 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 76

Siemens SINAUT MD720-3 Скачать руководство пользователя страница 60

SINAUT MD720-3 in OPC Mode

SINAUT MD720-3

60

C79000-G8976-C211

5.4

PIN in OPC-Mode

Enter the PIN

If the LED “S” blinks slowly (1 time per second), the SINAUT MD720-3 waits for a
PIN entry.

In OPC-Mode the PIN is sent by the connected PLC to the SINAUT MD720-3.
Therefore you need to enter the PIN in the data module of your SPS program with
reference to the program module WDC_INIT (See System manual SINAUT MICRO
SC). Please check if the PLC and the SINAUT MD720-3 are connected together.

The LED S (Status) blinks fast

If the LED S blinks fast (4 times per second), either the SIM card was not detected
or he SIM card is PUK-blocked, because a wrong PIN has been entered too often.

1. Please check, if the SIM card has been inserted correctly into the device (refer

to chapter 2

Inserting the SIM card

).

2. Please check, if the SIM card is PUK-blocked. Insert the SIM card into a

common mobile phone. The mobile phone will display, if the SIM card is PUK-
blocked. If the SIM card is PUK-blocked, please enter the PUK and then a PIN.
You can use a common mobile phone to do this.

3. Before you enter again the SIM card into the SINAUT MD720-3, please

investigate why the SIM card has been PUK-blocked: Which PIN have you
entered into your PLC program?

4. Please check and eventually reset the parameter SIMSTATE of the SINAUT

MD720-3.

Check and reset the parameter SIMSTATE

The parameter SIMSTATE will be displayed when you press the SET button (refer
to 6.2

Getting the current settings and values

):

SIMSTATE=SIM_OK

Ready for operation

SIMSTATE=SIM_ERROR Wrong

PIN; one wrong PIN entry

SIMSTATE=SIM_PROBLEM

Wrong PIN; two wrong PIN entries or no SIM
detected

In case of SIMSTATE=SIM_ERROR or SIMSTATE=SIM_PROBLEM please
proceed as follows:

«
...
58
59
60
61
62
...
»

Содержание SINAUT MD720-3













































































Отзывы:

Нет отзывов