manualshive.com logo in svg

Siemens SINAUT MD720-3, Системное руководство, Страница: 32 / 76

Поделиться
Скачать
Siemens SINAUT MD720-3 Скачать руководство пользователя страница 32

SINAUT MD720-3 in Terminal Mode 

 

SINAUT MD720-3 

32 

C79000-G8976-C211 

 

ATI 

Request identification information 

Read command 

 

Command: 

ATI[<value>] 

Response: 

<text> (depends on <value>) 
OK

 

Parameter: <value>: 

 

none: 

Product name and Firmware Version 

0: 

Product name and Firmware Version 

1: 

Product name, Interface, Mode  

3: 

Product name and Firmware Version 

Notice: 

<text> may take more than one line

 

 

ATO 

Switch from command mode to data mode 

Executive command

 

Command: 

ATO[n] 

Response: 

Device returns to data mode from command mode: 
CONNECT <text> 
If connection is not successfully resumed 
NO CARRIER 

Parameter: <n>: 

0 

switch from command mode to data mode 

Notice: 

ATO corresponds to the +++ escape sequence.  

 

ATQ 

Set result code presentation mode 

Executive command

 

Command: 

ATQ[<n>] 

Response: 

OK 

(if <n> = 0) 

Nothing 

(if <n> = 1)

 

Parameter: 

<n>:  
0: 

result codes transmitted by the device <Default> 

1: 

no result code transmitted by the device 

Notice: 

Specifies whether or not the device transmits any result code to the application. 
Information text transmitted in response is not affected by this setting.

 

 
 

ATS0? 

Shows Automatic answering settings 

Read command

 

Command: 

ATS0? 

Response: <n> 

OK 

Parameter: 

See  ATS0=<n> 

Notice: - 

Содержание SINAUT MD720-3













































































Отзывы:

Нет отзывов