Siemens SINAUT MD720-3 Скачать руководство пользователя страница 66

Страница: 66 / 76

Service functions

SINAUT MD720-3

C79000-G8976-C211

6.3

Service mode to upload a new firmware

When the service mode is active you can update the firmware of SINAUT MD720-
3.

The firmware contains the fundamental programming of the SINAUT MD720-3. If
the manufacturer has produced new firmware, for example to equip the device with
new functions, then this can be loaded into the SINAUT MD720-3.

You can find the latest firmware in the internet on the pages of des Siemens
Service & Support (see Foreword).

To update the firmware please proceed as follows.

Switch on the service mode and connect the device to a PC

1. Push the SET button for 2 up to 4 seconds until the LED “Q” in ON, while the

SINAUT MD720-3 is in operation. The device switches into the service mode.

2. Connect a PC to the interface X1 of the SINAUT MD720-3.

Installation of the modem driver

For the communication with the SINAUT MD720-3 in service mode you need to
install a modem driver.

1. Open

the

Control Panel

in the Start Menu.

2. Using Windows XP opens the category

Printers and Other Hardware

or switch

to the Classic View.

3. Open

the

Phone and Modem Options

4. Select

Add

in the register

Modems

5. Please follow the

Hardware-Wizard

6. Select

Don’t detect my modem; I will select it from a list a

nd click

Next.

7. Select from the manufacturer list

Standard Modem Types

the

Standard 19200

bps Modem

and click

Next.

8. Select the COM-Port of your computer, the SINAUT MD720-3 is connected to

and clicks

Next.

9. Wait until the modem installation has been finished and click

Finish

10. In the

Phone and Modem Options

menu the

Standard 19200 bps

Modem is

listed now.

Содержание SINAUT MD720-3













































































Результаты поиска

Содержание SINAUT MD720-3

Отзывы:

Siemens SINAUT MD720-3, Системное руководство, Страница: 66 / 76

Результаты поиска

Содержание SINAUT MD720-3

Отзывы: