Siemens SINAUT MD720-3 Скачать руководство пользователя страница 34

Страница: 34 / 76

SINAUT MD720-3 in Terminal Mode

SINAUT MD720-3

C79000-G8976-C211

AT\Q

Hardware Flow Control on/off

Executive command

Command:

AT\Q<n>

Response OK
Parameter: <n>:

Hardware Flow Control (RTS/CTS) off

Hardware Flow Control (RTS/CTS) on

Notice: -

ATX

Set CONNECT result code Format und Call monitoring

Executive command

Command:

ATX[<value>]

Response: OK
Parameter: <value>:

0 :

CONNECT result code only returned, dial tone and busy detection are both
disabled <Default>

1 :

CONNECT<text> result code only returned, dial tone and busy detection are
both disabled

2 :

same as 1

3 :

same as 1

4 :

same as 1

Notice:

The term “tone” is used in analogue telephone networks. The status “No dialtone” will
usually not appear, as soon as the device is booked into a GSM network. A Busy
message will be transmitted.

AT&C

AT&C Set circuit Data Carrier Detect (DCD) function mode

Executive command

Command:

AT&C[<value>]

Response:

Parameter: <value>:

0 :

DCD line is always ON

1 :

DCD line is ON in the presence of data carrier only. <Default>

Notice:

Содержание SINAUT MD720-3













































































Результаты поиска

Содержание SINAUT MD720-3

Отзывы:

Siemens SINAUT MD720-3, Системное руководство, Страница: 34 / 76

Результаты поиска

Содержание SINAUT MD720-3

Отзывы: