Siemens SINAUT MD720-3 Скачать руководство пользователя страница 47

Страница: 47 / 76

SINAUT MD720-3 in Terminal Mode

SINAUT MD720-3
C79000-G8976-C211

AT+CMGF Select SMS message format

Test

Command:

AT+CMGF=?

Response:

+CMGF: (list of supported <mode>s)
OK

Read command

Command:

AT+CMGF?

Response: +CMGF:

<mode>

Executive command

Command:

AT+CMGF=[<mode>]

Response: OK
Parameter: <mode>:

0 PDU

mode

1 Text

mode

Notice: -

AT+ CMGL

List SMS messages from preferred storage

Test

Command:

AT+CMGL=?

Response:

+CMGL: (list of supported <stat>s)
OK

Executive command

Command:

AT+CMGL[=<stat>]

Response:

In text mode (+CMGF=1) and successfully executed command and SMS-SUBMITs
and/or SMS-DELIVERs:
If <stat> = "REC READ" or "REC UNREAD"

+CMGL: <index>,<stat>,<oa/da>,<scts>,<length>
<CR><LF><data><CR><LF>
[+CMGL: <index>,<stat>,<oa/da>,<scts>,<length><CR><LF><data>
<CR><LF>[...]]

If <stat> = "STO UNSENT" or "STO SENT"

+CMGL: <index>,<stat>,<oa/da>,<length>
<CR><LF><data><CR><LF>
[+CMGL: <index>,<stat>,<oa/da>,<length><CR><LF><data>
<CR><LF>[...]]

In other cases:

+CMS ERROR: <err>

In PDU mode (+CMGF=0) and successfully executed command:

[+CMGL: <index>,<stat>,[<alpha>],<length><CR><LF><pdu>
[<CR><LF>+CMGL:<index>,<stat>,[<alpha>],<length><CR><LF><pdu>
[...]]]
OK

Содержание SINAUT MD720-3













































































Результаты поиска

Содержание SINAUT MD720-3

Отзывы:

Siemens SINAUT MD720-3, Системное руководство, Страница: 47 / 76

Результаты поиска

Содержание SINAUT MD720-3

Отзывы: