Siemens SINAUT MD720-3 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 76

Siemens SINAUT MD720-3 Скачать руководство пользователя страница 49

SINAUT MD720-3 in Terminal Mode

SINAUT MD720-3
C79000-G8976-C211

49

AT+CMGR Read SMS message

Test

Command:

AT+CMGR=?

Response: OK

Executive command

Command:

AT+CMGR=<index>

Response:

In text mode (+CMGF=1)

If command is executed successfully and SMS-DELIVER:
+CMGR: <stat>,<oa>,<scts>,<length>
<CR><LF><data><CR><LF>
If command is executed successfully and SMS-SUBMIT:
+CMGR: <stat>,<da>,<length>
<CR><LF><data><CR><LF>
In other cases:
+CMS ERROR: <err>

In PDU mode (+CMGF=0) and successfully performed command

:

+CMGR: <stat>,[<alpha>],<length><CR><LF><pdu>
OK

Parameter:

Refer to +CMGL

Notice:

Execution command returns message with location value <index> from preferred
message storage <mem1>. Status of the message and entire message data unit <pdu> is
returned. If status of the message is 'received unread', status in the storage changes to
'received read'.

«
...
47
48
49
50
51
...
»

Содержание SINAUT MD720-3













































































Отзывы:

Нет отзывов