Siemens SINAUT MD720-3 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 76

Siemens SINAUT MD720-3 Скачать руководство пользователя страница 41

SINAUT MD720-3 in Terminal Mode

SINAUT MD720-3
C79000-G8976-C211

41

Notice:

The execute command specifies PDP context parameter values for a PDP context
identified by the (local) context identification parameter, <cid>. The number of PDP
contexts that may be in a defined state at the same time is given by the range returned by
the test command.
A special form of the set command, +CGDCONT= <cid> causes the values for context
number <cid> to become undefined.

AT+CGATT GPRS Attach or Detach

Test

Command:

AT+CGATT=?

Response:

+CGATT: (list of supported <state>s)

Read command

Command:

AT+CGATT?

Response: +CGATT:

<state>

Executive command

Command:

+CGATT=<state>

Response:

OK

Parameter: <state>:

Indicates the state of GPRS attachment
0: detached
1: attached

Notice:

-

AT+CIMI

Request international subscriber identity

Test

Command:

AT+CIMI=?

Response: OK

Read command

Command:

AT+CIMI

Response:

<IMSI> (International Mobile Subscriber Identify)
OK

Parameter: -
Notice: -

«
...
39
40
41
42
43
...
»

Содержание SINAUT MD720-3













































































Отзывы:

Нет отзывов