Sea Recovery Aqua Whisper DX 1400-2, Руководство пользователя

Страница: 119 / 226

Aqua Whisper DX Modular 450-1800
Page 7-11
Opera
tion
6. SRC MCC-3, Membrane Cleaning Compound “#3”
is used for iron fouling. It is not included in the SRC
Membrane Cleaning Chemical kit. If the system’s
R.O. membrane element is fouled with rust from
iron piping, then SRC CC-3 may be used for
effective removal of light or moderate rust fouling.
Heavily rust fouled RO membranes may not be
recoverable as rust not only fouls the Membrane
Element but also damages the membrane surface.
WARNING
: DO NOT mix different
chemicals together. DO NOT use
different cleaning chemicals together
at the same time. Mix the cleaning
chemicals separately and use them
separately. Use only Sea Recovery
supplied chemicals. NEVER use third
party non-Sea Recovery chemicals.
CLEANING PROCEDURE
Product Water Required, in U.S. Gallons for Cleaning of
the R.O. membrane element:
Chemical Rinse
water
required
Cleaning
water
required Second
rinse
water
required Total
water
required
CC-1 10 10 10 30
CC-2 10 10 20
CC-3 10 10 20
1. Close the Inlet Sea Cock Valve.
2. If installed, position the Multi Media Filter Valves
in the Multi Media Filter By-Pass position to
by-pass it during the cleaning procedures See
illustration on page 7-12 for Multi Media Filter
Valve positioning.
3. Replace the Pre-filtration Cartridge with a new
SRC supplied Pre-filtration Element.
4. Fill a 10-gallon (37.8 liters) container with
unchlorinated clean fresh water.
5. Configure the system for a Once Through Rinse as
illustrated on Page 7-7.
6. Start the System in the MANUAL MODE
Operation of the System will deplete the Fresh
Water in the bucket. Just prior to depleting the
Water in the Bucket Touch STOP.
7. Once again, fill the container with 10 gallons (37.8
liters) clean, fresh water.
8. Add to the 10 gallons (37.8 liters) of fresh water
1.5 lbs. (0.68 kg) of Sea Recovery Membrane
Cleaning Compound MCC 1, MCC 2 or MCC 3.
Thoroughly mix the solution until the cleaning
compound has dissolved.
9. Configure the system for a Recirculating Closed
Loop configuration as illustrated on Page 7-7.
10. Start the System in the MANUAL MODE
11. Operate the System in the Recirculating Closed
Loop configuration for 60 minutes. After 60
minutes stop the system as follows:
12. Configure the system for a Once Through Rinse
configuration as illustrated on Page 7-7.
13. Start the System in the MANUAL MODE to
discharge the cleaning chemical to waste.
Operation of the System will deplete the cleaning
solution in the bucket. Just prior to depleting the
solution in the Bucket stop the System.
14. One final time, fill the container with 10 gallons
(37.8 liters) clean, fresh water.
15. Configure the system for a Recirculating Closed
Loop configuration as illustrated on Page 7-7.
16. Start the System in the MANUAL MODE
Operate the System in the Recirculating Closed
Loop configuration for 10 minutes. After 10
minutes stop the system as follows:
17. Configure the system for a Once Through Rinse
configuration as illustrated on Page 7-7.
18. Start the System in the MANUAL MODE to
discharge the rinse water to waste.
Operation of the System will deplete the cleaning
solution in the bucket. Just prior to depleting the
solution in the Bucket Stop the System as follows:
The system is now ready for additional cleaning,
use, or storing.
If further membrane cleaning is necessary, repeat
Steps 4 to 18 above for each additional cleaning.
19. If System will be expose to freezing temperature,
proceed to Section 7.5: