Sea Recovery Aqua Whisper DX 1400-2, Руководство пользователя

Страница: 86 / 226

Aqua Whisper DX Modular 450-1800
Page 5-4
Installa
tion
13. Allow sufficient space after the Commercial Prefilter
for the Inline Vacuum/Pressure Gauge, if used.
14. The no-charge optional Oil/water Separator is
mounted to a flat horizontal surface using the
supplied screws. Maintain an orientation and
accessibility that allows the operator access to
remove the filter element for maintenance. Allow
minimum 12 in. (30.5 cm) above the top of the
housing for filter element removal. Mount the Oil/
water Separator in close proximity to the outlet of
the Booster Pump and the System frame.
Refer to
PAGE 5-3, fig. 5b
WARNING NOTE
(Refer to pg. 5-3, fig. 5b.)
:
The Oil/water Separator utilizes the same
filter housing as the Commercial Prefilter.
However, the Oil/Water Separator is
plumbed opposite of (backwards from)
the Commercial Prefilter. This filter
housing has a raised arrow molded
into the housing indicating flow and the
inlet and outlet ports are also marked
with raised lettering Inlet and Outlet
molded into the housing. For the Oil/
Water Separator these markings are
INCORRECT. The Oil/Water Separator’s
correct water flow enters the center
core of the filter element and migrates
to the outer surface of the filter element
(opposite that of the Commercial prefilter).
Prior to shipping Sea Recovery has placed Inlet
and Outlet labels (stickers) indicating the correct
plumbing. Follow the stickers, not the molded
arrow and lettering.
Refer to PAGE 5-4.
15. Pressure Differential Transducer.
The optional Pressure Differential Transducer
threads into the center port of the Low Pressure
Transducer Manifold.
CAUTION : Take care to NOT cross the
fine female threads in the manifold.
Thread in clockwise finger tight. Using a wrench
tighten an additional 45 degrees.
DO NOT OVER TIGHTEN.
OVER TIGHTENING WILL STRIP THE MANIFOLD
FEMALE THREADS.
Using the supplied 1/4 in. (6.35 mm) O.D.
tubing connect the center Pressure Differential
Transducer Tube Fitting to the T-Connector
Pressure Pick-Up or to the Pressure Pick Up port
of the respective Prefiltration component. Refer
to the various Piping and Interconnect Diagrams
Illustrated in this Section 3.
16. The HP Pump is mounted to a flat horizontal
surface using the 4 supplied 5/16-18x3/4 SS Hex
bolts, nuts and washer. The HP Pump is mounted
in an accessible location to allow access for
maintenance.
Set the HP Pump in place onto a flat surface and
mark the mounting holes.
Move the HP Pump out of the way and drill the
appropriate hole depending on which hardware
will be used. Place the HP Pump over the drilled
holes and attach the rubber isolation grommet
under the plate at each of the 4 mounting holes.
17. RO Membrane Presure Vessels must be mounted
on a flat or vertical surface close to the HP
Pump. If possible allow 27-47 in. (68.6-119.4
cm) clearance at the ends for RO Membrane
maintenance.
The Pressure Vessel assembly can be removed
entirely from surface for maintenance.
18. UV Sterilizer Installation. The Ultra Violet Sterilizer
should be mounted on a flat horizontal or vertical
wall. Refer to Section 5.8 for installation details.
19. The Fresh Water Flush Carbon Filter is mounted
to a flat vertical surface in an accessible location
for filter element changing. Choose a location
between the Automatic Fresh Water Flush Check
Valve and a pressurized line from the boat’s fresh
water pressure system.
CAUTION : In order to provide the
required flow of water to the Aqua
Whisper System during the Fresh Water
Flush cycle, the Boat or Home’s fresh
water pressure system must deliver
minimum 1 U.S. Gallons (3.8 Liters) Per
Minute at minimum 25 PSI and maximum
60 PSI (minimum 172 kPa and maximum
414 kPa).