Sea Recovery Aqua Whisper DX 1400-2, Руководство пользователя

Страница: 141 / 226

Aqua Whisper DX Modular 450-1800
Page 8-17
Maintenance
To replace the pH Neutralizing Cartridge:
a) Unscrew the bowl counter clockwise.
b) Remove the pH Neutralizing Cartridge from
the bowl.
c) Remove the O-Ring from the top of the bowl
and take care to not damage it.
d) Replace the pH Neutralizing Cartridge with a
new Sea Recovery Cartridge.
e) Wipe the O-Ring with a damp cloth.
f) Sparingly lubricate the O-Ring lightly with
O-Ring lubricant.
g) Place the O-Ring back onto the bowl.
h) Insert the new, Sea Recovery pH Neutralizing
Cartridge into the bowl.
i) Screw the bowl on clockwise.
j) Hand snug to seal the O-Ring, do not
use a wrench or other tool to tighten, do
not over tighten. Over tightening causes
stress to the lid and bowl threads resulting
in damage, breakage, or cracks and
subsequent removal difficult.
31. Ultraviolet Sterilizer: The UV Sterilizer lamp emits
a low frequency form of light. This light degrades
and loses intensity and ability to sterilize biological
matter over approximately 8,000 hours of use.
Therefore, the lamp may remain lit, but requires
replacement every 4400-8000 hrs.
CAUTION : Make sure that system power
is turned off before beginning sterilizer
maintenance. Ultra Violet light is harmful
to eyes and skin.
Lamp Replacement:
a) Remove the four screws on the ballast box
and remove lid.
b) Remove the rubber boot and carefully pull
lamp out of the quartz sleeve.
c) Replace the lamp. During lamp replacement
clean the quartz sleeve as well. The quartz
sleeve should be crystal clear and if it has
discolored, it must be cleaned or replaced.
Quartz Sleeve Cleaning:
a) Remove the four screws on the ballast box
and remove lid.
b) Remove the rubber boot and carefully pull
lamp out of the quartz sleeve.
c) Unscrew and remove the two compression
nuts (ballast box and view port).
d) Remove the O-ring on the view port side only.
e) With care pull the quartz sleeve out from the
ballast box side.
f) Clean the quartz tube with water and a bottle
brush without moving the O-ring. Dry with a
soft cloth. Handle the quartz sleeve carefully.
Reassembly:
a) Replace old O-rings with new O-rings.
b) Insert the quartz sleeve (close-end first)
through the ballast box passthru until O-ring
contact passthru. Screw on the ballast box
compression nut. Insert view port O-ring and
screw on view port compression nut .
c) Attach a new UV Lamp into the plug.
d) Slide the lamp into the Quartz Sleeve and
install rubber boot over the compression nut.
e) Replace the three 1/4-20 cap head screws.
32. Fresh Water Flush Carbon Filter Element: The
Carbon Filter Element in the Fresh Water Flush
should be replaced every 3 months.
The Fresh Water Flush will automatically flush
the system with Fresh Water every preset number
of days. The duration of the flush cycle will be 90
seconds for a system connected to 60 Hz power
and to 120 seconds for systems connected to 50
Hz power.
To replace the Carbon Filter Element:
a) Unscrew the bowl counter clockwise.
b) Remove the Carbon Filter Element from
the bowl.
c) Remove the O-Ring from the top of the bowl
and take care to not damage it.
d) Replace the Carbon Filter Element with a new
Sea Recovery element.
e) Wipe the O-Ring with a damp cloth.
f) Sparingly lubricate the O-Ring lightly with
O-Ring lubricant.
g) Place the O-Ring back onto the bowl.
h) Insert the new, Sea Recovery Carbon Filter
Element into the bowl.