Sea Recovery Aqua Whisper DX 1400-2, Руководство пользователя

Страница: 126 / 226

Aqua Whisper DX Modular 450-1800
Page 8-2
Maintenance
Many of these special components can appear to be
similar to Sea Recovery components. Extensive and
expensive damage to the Sea Recovery System WILL
result if incompatible components are used in the Sea
Recovery System. Damage caused to the Sea Recovery
System as a result of third party components is the
liability and responsibility of both the Marine Dealer that
sold the component for use in the Sea Recovery System
as well as the Owner/Operator that purchased and
installed the third party component in the Sea Recovery
System and is not covered by the Sea Recovery Warranty.
Always insist on only Sea Recovery supplied components,
spares, and consumable.
8.3 INDIVIDUAL COMPONENT MAINTENANCE
AND REPAIR
Refer to the P&ID in Section 3.
1.
Inlet Thru Hull Fitting: Non Sea Recovery
component. Keep the Inlet Thru Hull Fitting free
and clear of debris and marine growth. If the Inlet
Thru Hull Fitting is clogged, this results in a low
feed pressure condition, which causes the system
to shut off.
Blockage at the Inlet Thru-Hull Fitting causes the
System to shut off due to lack of Feed Water Flow.
Unfortunately, since it is under water operators
are reluctant to thoroughly inspect the Inlet Thru-
Hull Fitting for problems. This can cause time
consuming frustrations in attempting to gain feed
water flow by trouble shooting other components
in the System.
The Inlet Thru-Hull Fitting must be free and clear
allowing the System to draw 4.5 U.S. Gallons
(17 Liters) Per Minute through it with minimal
resistance. Any blockage at the Inlet Thru-Hull
Fitting will cause low pressure and low flow
problems at the System. This Inlet Thru-Hull
Fitting must be a Forward Facing Scoop so that
the System receives a positive flow of water as
the boat is under way. It must be minimum 3/4 in.
(19 mm) inside diameter. It must be installed in a
position on the bottom of the Hull so as to allow
free flowing Feed Water without air.
CAUTION : A flat profile, flush mount,
inlet thru-hull fitting will cause a vacuum
as the boat is under way, and this
will cause loss of feed water flow and
product water can be used to remove any feed
water residue from the exterior surfaces of the
components.
USE OF NON-AUTHORIZED OR
MISUSE OF AUTHORIZED CHEMICALS
VOIDS SYSTEM WARRANTY.
8.1 WEEKLY QUICK CHECK
The following steps ensure that potential problems are
resolved preventing major repairs:
1.
Inspect all fasteners for tightness including
brackets, screws, nuts, and bolts. Pay special
attention to the High Pressure Pump and Electric
Motor since they are subject to increased vibration.
2. Clean any salt water or salt deposits from the
system with a wet rag.
3. Check for water leaks throughout the System and
supporting water lines.
4. Check all tubing and high-pressure hoses for wear
and abrasion against rough surfaces. The hoses
must not contact heated or abrasive surfaces.
8.2 OPERATOR MAINTENANCE INTERVALS
The frequency of required maintenance is dependent on
the regularity of usage, the condition of the intake water
(the location of use), the length of time the system is
exposed to water, the total running time and, in some
cases, the manner in which the system is installed
or operated. Because of these factors, it is virtually
impossible to comprise an exact timetable for required
maintenance. The maintenance timetable, Page 8-3, is
an estimate of the time intervals at which maintenance
may be required on the various system components. This
is based upon factual data compiled from Sea Recovery
installations around the world. However, this schedule
must be adjusted to each individual system depending
upon the variables listed.
WARNING
: Components, spares,
and consumable utilized within the
Sea Recovery System can be specific
to Sea Recovery specifications and are
not commercially available from other
sources. Other Components utilized
within the Sea Recovery System are
modified by Sea Recovery for a specific
purpose of compatibility and are not
commercially available from other sources.