background image

Page 23 of 44

P/N 595189-01  Rev A  4/10

donning The reSPirATor hArneSS 

conTinued on nexT PAge...

Adjust  the  shoulder  strap  tri-slide  buckle  so  that  it  remains  in  place 

on the right shoulder and holds the waist belt at waist level. Ensure 

that  the  regulator  hose  is  secured  in  the  snap  loop  on  the  shoulder 

pad. See FIGURE 16. 

WArning

don  The  body  hArneSS  before  don-

ning  The  necK  STrAP  AS  inSTrucTed.  

inTerference beTWeen The Shoulder 

STrAP  And  The  necK  STrAP  mAy  in-

Terfere WiTh ProPer donning of The 

fAcePiece  in  An  emergency  W h i c h 

c o u l d   r e S u l T   i n   S e r i o u S   i n J u r y 

or  deATh.

ADJUSTING THE SHOULDER STRAP 

figure 16

If  any  other  safety  equipment  is  to  be  used  with  the  SKA-PAK AT, 

such as fall protection equipment or communication equipment, verify 

that the equipment does not interfere with the operation of the SKA-

PAK  AT  in  any  way.  Verify  that  the  SKA-PAK  AT  air  lines  are  not 

obstructed  and  that  nothing  will  interfere  with  the  face  to  facepiece 

seal  or  dislodge  the  facepiece  from  the  user's  face  in  usage.  If  any 

obstruction  or  interference  is  suspected,  do  not  use  the  respirator 

until the problem is corrected.

Position  the  required  length  of  air  supply  hose  and  prepare  it  for 

use by connecting the segments to each other and to the air supply 

system. Adjust the pressure at the air supply system to the operating 

pressure of the respirator. Repeat this step for each air supply hose 

and each air supply system to be used.

Adjust  all  head  straps  to  the  full  outward  position.  On  respirators 

equipped with a neck strap, place the body harness on the shoulder 

before placing the neck strap around the neck. Position the facepiece 

in a ready to don position using the Scott Neck Strap Assembly. See 

ACCESSORIES.

WArning

do  noT  uSe  Any  oTher  SAfeTy  eQuiP-

menT  WiTh  The  SKA-PAK  AT  Which  in-

TerfereS  WiTh  The  oPerATion  of  The 

SKA-PAK  AT  or  Which  mAy  cAuSe  The 

fAcePiece To be Pulled from The uS-

er’S  fAce  exPoSing  The  uSer  To  The 

hAZArdouS ATmoSPhere The reSPirA-

Tor WAS inTended To ProTecT AgAinST. 

fAilure To verify ThAT The SKA-PAK AT 

Will oPerATe ProPerly mAy reSulT in 

SeriouS inJury or deATh.

ADJUSTING THE WAIST BELT 

figure 15

Adjust the waist belt. Tighten or loosen the waist belt by sliding the 

waist belt tri-slide buckle. See FIGURE 15. 

Содержание SKA-PAK AT













































Отзывы: