background image

Page 43 of 44

P/N 595189-01  Rev A  4/10

cAuTionS And limiTATionS

D – AIR LINE RESPIRATORS CAN BE USED ONLY WHEN THE RESPIRATORS ARE SUPPLIED WITH RESPIRABLE 

AIR MEETING THE REQUIREMENTS OF CGA G-7.1 GRADE D OR HIGHER QUALITY.

E – USE ONLY THE PRESSURE RANGES AND HOSE LENGTHS SPECIFIED IN THE USER'S INSTRUCTIONS.
I –  CONTAINS ELECTRICAL PARTS WHICH HAVE NOT BEEN EVALUATED AS AN IGNITION SOURCE IN FLAMMABLE 

OR ExPLOSIVE ATMOSPHERES BY MSHA/NIOSH.

J –  FAILURE TO PROPERLY USE AND MAINTAIN THIS PRODUCT COULD RESULT IN INJURY OR DEATH.
M – ALL APPROVED RESPIRATORS SHALL BE SELECTED, FITTED, USED AND MAINTAINED IN ACCORDANCE WITH 

MSHA, OSHA AND OTHER APPLICABLE REGULATIONS.

N – NEVER SUBSTITUTE, MODIFY, ADD OR OMIT PARTS.  USE ONLY ExACT REPLACEMENT PARTS IN THE CON-

FIGURATION AS SPECIFIED BY THE MANUFACTURER.

O – REFER TO USER'S INSTRUCTIONS AND/OR MAINTENANCE MANUALS FOR INFORMATION ON USE AND MAIN-

TENANCE OF THESE RESPIRATORS.

S – SPECIAL  OR  CRITICAL  USER'S  INSTRUCTIONS AND/OR  SPECIFIC  USE  LIMITATIONS APPLY.    REFER TO  IN-

STRUCTION MANUAL BEFORE DONNING. 

S--SPeciAl or criTicAl uSer'S inSTrucTionS

APPROVED  FOR  RESPIRATORY  PROTECTION  DURING  ENTRY  INTO AND  ESCAPE  FROM  OxYGEN  DEFICIENT 

ATMOSPHERES, GASES, AND VAPORS, WHEN USING THE AIRLINE SUPPLY.
APPROVED FOR ESCAPE ONLY WHEN USING THE SELF CONTAINED AIR SUPPLY.
APPROVED FOR USE AT TEMPERATURES ABOVE -25°F / -32° C.
APPROVED  ONLY  WHEN  THE  COMPRESSED-AIR  CYLINDER  IS  FULLY  CHARGED  WITH AIR  MEETING  THE  RE-

QUIREMENTS OF THE COMPRESSED GAS ASSOCIATION SPECIFICATION G-7.1 FOR TYPE 1, GRADE D AIR, OR 

EQUIVALENT SPECIFICATIONS.
THIS APPROVAL APPLIES  ONLY  WHEN  THE  DEVICE  IS  SUPPLIED  WITH AIR  FROM  THE  SELF-CONTAINED AIR 

SUPPLY OR RESPIRABLE BREATHING AIR.
IF THE SUPPLIED-AIR FAILS, PROCEED TO FRESH AIR IMMEDIATELY.
REFER TO TABLE 1 ON PAGE 23 FOR LIMITATIONS AND OPERATING INSTRUCTIONS FOR SUPPLY HOSE.
WHEN  USING  FACEPIECE  803921-01,  803921-02,  803921-03,  OR  803921-08 AT TEMPERATURES  BELOW  +32°

 

F  / 

0° C ADD OPTIONAL NOSE CUP ASSEMBLY 802819-01.
SEE  LOW  TEMPERATURE  OPERATION  SECTION  OF  THIS  INSTRUCTION  MANUAL  FOR ADDITIONAL  INFORMA-

TION.
THE CONTAINER SHALL MEET APPLICABLE DOT SPECIFICATIONS.
SEE  THE  REGULAR  OPERATIONAL  INSPECTION  SECTION  OF  THE  INSTRUCTION  MANUAL  FOR  ADDITIONAL 

INFORMATION.
THE SCOTT VOICE AMPLIFIER AND OTHER SCOTT COMMUNICATIONS DEVICES CAN ONLY BE USED WITH FACE-

PIECES EQUIPPED WITH DUAL VOICEMITTERS.

WArning

imProPer  uSe  of  A  reSPirATor  mAy  reSulT  in  SeriouS  inJury  or  deATh.  imProPer  uSe 

includeS, buT iS noT limiTed To, uSe WiThouT TrAining, diSregArd of The WArningS And 

inSTrucTionS SuPPlied WiTh The reSPirATor And iTS AcceSSorieS And fAilure To inSPecT 

And  mAinTAin  The  reSPirATor.  reAd  And  underSTAnd  The  inSTrucTion  mAnuAl  And  Any 

APPlicAble AcceSSory inSTrucTionS And WArningS before ATTemPTing To uSe A reSPirATor.

Содержание SKA-PAK AT













































Отзывы: