Sanyo SAP-KCRV243GJ Скачать руководство пользователя страница 74

Страница: 74 / 78

Details of Self-Diagnostics

When the operation selector on the indoor unit is moved from the ON or TEST position to the OFF (Self-diagnostics)

position, the indicator lamps on the indoor unit will flash (or remain ON) for 5 seconds and then turn OFF for 2 seconds

(buzzer sounds once) to indicate the presence of a sensor failure or the activation of a protective function.

Self-diagnostics is completed when the buzzer sounds 3 beeps.

If there is no trouble, the lamps do not flash (illuminate). Also note that the corresponding parts listed below may not be

present in some models.

Indication on indoor unit

Timer

Operation

Room temperature sensor failure

Code

Diagnostics item

Diagnostics contents

Indoor heat exchanger sensor failure

Humidity sensor failure

Compressor temperature sensor failure
SH sensor failure

Outdoor heat exchanger sensor failure
Outdoor narrow tubing sensor failure

Outdoor air temperature sensor failure
Outdoor wide tubing sensor failure

Outdoor electrical current sensor failure

Indoor/outdoor communications failure
(serial communications)

HIC circuit failure
Power Tr circuit failure

Outdoor unit external ROM failure

Peak current cut-off

PAM circuit failure
Active circuit failure

Compressor discharge overheat
prevention

Indoor fan operating failure

4-way valve switching failure
Indoor zero-cross failure

DC compressor drive circuit failure

No-refrigerant protection

Outdoor AC fan operating failure

Outdoor system communications failure
Outdoor high-voltage SW, OLR operation
Outdoor power supply open phase,
outdoor col freezing

Freeze-prevention operation

Outdoor circuit board failure

Miswiring

AC power failure

Blown fuse

Power relay failure

Indoor or outdoor circuit board failure

HIC or power Tr failure

Outdoor fan does not turn

Instantaneous power outage

Service valve not opened

Outdoor fan blocked

Continuous overload operation

Compressor failure

Outdoor circuit board failure

Instantaneous power outage

HIC or power Tr failure

Outdoor circuit board failure

Outdoor power supply voltage failure

Electric expansion valve failure

Capillaries blocked

No gas

Continuous

overload operation

Outdoor fan does not turn

Outdoor circuit board failure

Fan motor failure

Contact failure at connector

Indoor circuit board failure

Miswiring

Blown fuse

Power relay failure

Open phase

Outdoor circuit board failure

Compressor failure

Indoor fan system failure

No refrigerant

Low-temperature operation

Other: Timer lamp flashes (3-second intervals).

NOTE: If the operation lamp continues to flash (orange) even when the indoor unit operation selector has been moved

to the OFF position, an indoor unit external ROM failure has occurred. (E14)

After inspection or repair is completed, be sure to move the operation selector to the DEMO position, turn the

power ON, and erase the diagnostics contents.

S01

S02

S03

S04

S05

S06

S07

E01

E02

E03

E04

E05

E06

E07

E08

E09

E10

E11

E12

E13

Sensor open circuit or short circuit
Contact failure at connector or open circuit at teminal
crimping location (short-circuit detection only for the
humidity sensor)
Indoor/outdoor circuit board failure

*
*

Sensor open circuit or short circuit

Contact failure at connector or opern circuit at terminal

crimping location

Outdoor circuit board failure

*
*

External ROM data failure

Outdoor circuit board failure

4-way valve failure

Outdoor circuit board failure

Service valve not opened

No refrigerant

Open phase

Outdoor circuit board failure

Fan motor failure

Contact failure at connector

Outdoor circuit board failure

...ON

...Flashing

...OFF

Содержание SAP-KCRV243GJ















































































Результаты поиска

Содержание SAP-KCRV243GJ

Отзывы:

Похожие инструкции для SAP-KCRV243GJ

Бренды по названию

Популярные бренды

Sanyo SAP-KCRV243GJ, Техническое и сервисное руководство

Результаты поиска

Содержание SAP-KCRV243GJ

Отзывы:

Похожие инструкции для SAP-KCRV243GJ

Бренды по названию

Популярные бренды