Sanyo SAP-KCRV243GJ Скачать руководство пользователя страница 48

Страница: 48 / 78

CAUTION

7-6. Test Run

Performing a test run

Refer to the test run procedures in the indoor unit

installation manual.

Perform the test run.

If the room temperature is 15˚C or below, it may not

be possible to check for tubing errors with cooling

operation. If this occurs, perform heating operation

and check that warm air is discharged from indoor unit.

If there is cold air mixed in with the warm air, check the

tubing connections again.

Checking tubing and wiring

Perform the test run and check that operation is nor-

mal.

Stop operation immediately if there is an error in

tubing or wiring. Turn the power (breaker) to OFF,

and check whether the inter-unit cables are con-

nected incorrectly. Correct the connections.

If there is an error in tubing, pump-down must be

performed. Be sure to perform pump-down. After

making corrections, again purge the air from the

tubes.

Содержание SAP-KCRV243GJ















































































Результаты поиска

Содержание SAP-KCRV243GJ

Отзывы:

Похожие инструкции для SAP-KCRV243GJ

Бренды по названию

Популярные бренды

Sanyo SAP-KCRV243GJ, Техническое и сервисное руководство

Результаты поиска

Содержание SAP-KCRV243GJ

Отзывы:

Похожие инструкции для SAP-KCRV243GJ

Бренды по названию

Популярные бренды