Sanyo SAP-KCRV243GJ Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 78

background image

34

In order to prevent charging
errors with A/C that uses R410A,
the screw diameter at the service
valve charging port has been
changed. When recharging or
performing other servicing, use
the special charging hose and
manifold gauge.

7-4. Air Purging

Air and moisture remaining in the refrigerant system

have undesirable effects as indicated below. There-

fore, they must be purged completely.

pressure in the system rises

operating current rises

cooling efficiency drops

moisture in the air may freeze and block capillary

tubing

water may lead to corrosion of parts in the refriger-

ant system

Air Purging with a Vacuum Pump

(for Test Run)

In order to protect the earth’s environment, be sure to

use a vacuum pump to perform the air purge.

(Never perform an air purge by using the refrigerant

gas cylinder or other external gas, or by using the gas

inside the outdoor unit.)

(1)

(2)

(3)

Check that each tube (both narrow and wide

tubes) between the indoor and outdoor units have

been properly connected and all wiring for the test

run has been completed. Note that both narrow

and wide tube service valves on the outdoor unit

are kept closed at this stage.

Using an adjustable wrench or box wrench,

remove the valve caps from the service valve on

both narrow and wide tubes.

Connect a vacuum pump and a manifold valve

(with pressure gauges) to the service port on the

wide tube service valve. (Fig. 20).

CAUTION

Cap tightening torque:
20-25 N-m
(200-250 kgf-cm)
(Tighten by hand, then
use a wrench to turn.)

Stopper

Spindle

Screw diameter: 1/2 (243 type)

5/8 (303 type)

UNF 20 threads

Valve core

Cap nut tightening torque:
7-11 N-m
(70-110 kgf-cm)
(Tighten by hand, then use a
wrench to turn approximately 30 ˚.)

<Structure of service valve on wide tube side>

Fig. 21

Be sure to use a manifold valve for
air purging. If it is not available,
use a stop valve for this purpose.
The “Hi” knob of the manifold
valve must always be kept closed.

CAUTION

Before using the vacuum pump
adapter, read the vacuum pump
adapter manual, and use the
adapter correctly.

CAUTION

When using a hex wrench to open the spindle, an

extremely small amount of refrigerant may leak.

This does not indicate a problem.

Use a hex wrench of a type to which force can be

easily applied.

Service valve
on narrow
tube side

Service
valve on
wide tube
side

CRV243

Hi

Lo

Hi

Lo

Lo

Lo

Lo

Lo

Lo

Manifold gauge
(special for R410A)

Low-
pressure
valve

Open

Leave the
valve open.

Vacuum pump
adapter
(for preventing
reverse flow)
(special for
R410A)

High-pressure valve

Hex wrench
(nominal size 4 mm, not provided)

Charging hose
(special for R410A)

Vacuum
pump

With push-pin

Fig. 20a

Fig. 20b

Service
valve on
narrow

Service
valve on
wide tube
side

Hex wrench

(nominal size 4 mm,

not provided)

With push-pin

Hi

Lo

Hi

Lo

Lo

Lo

Lo

Lo

Lo

Manifold gauge
(special for R410A)

Low-pressure

valve

Open

Leave the
valve open.

Vacuum pump
adapter
(for preventing
reverse flow)
(special for
R410A)

High-pressure valve

Charging hose
(special for R410A)

Vacuum
pump

CRV303

«
...
35
36
37
38
39
...
»

Содержание SAP-KCRV243GJ















































































Отзывы:

Нет отзывов

Похожие инструкции для SAP-KCRV243GJ

Бренд: b-mola Страницы: 9

Бренд: S&S Cycle Страницы: 8

Бренд: Haier Страницы: 22

Бренд: Danby Страницы: 26

Бренд: BASETech Страницы: 12

Бренд: Daikin Страницы: 12

Бренд: Nortek Страницы: 16

Бренд: EarthLinked Страницы: 11

Бренд: Kaysun Страницы: 16

Бренд: Daikin Страницы: 72

GWH18RC-K3DNA1A

Бренд: Gree Страницы: 92

Бренд: Rasonic Страницы: 28

Бренд: airo COMFORT Страницы: 8

Бренд: Nordyne Страницы: 20

climaVAIR V 7-025 NW

Бренд: Vaillant Страницы: 26

Бренд: Ocean Breeze Страницы: 18

Бренд: Olimpia splendid Страницы: 24

Бренд: OION Technologies Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды