Sanyo SAP-KCRV243GJ Скачать руководство пользователя страница 69

Страница: 69 / 78

Care and Cleaning (continued)

Anti-Mold Filter

The anti-mold filter behind the air intake grille should be checked and cleaned at least

once every two weeks.

Cleaning

Use a vacuum cleaner to remove light dust. If there is sticky dust on the filter, wash the

filter in lukewarm, soapy water, rinse it in clean water, and dry it.

How to replace the

anti-mold filter

1. With the "FRONT" mark facing you,

slide the anti-mold filter up into the

unit and then lower the handle into

the groove on the unit.

Air intake grille

Anti-mold
filter

Insert into the groove on the unit.

2. After installing the anti-mold filter, press

the locations marked by the arrows

( ) and close the air intake grille.

How to remove the

anti-mold filter

1. Grasp both ends of

the air intake grille

and pull it out and up.

2. Push the anti-mold

filter up slightly, and

then pull it down.

Air intake grille

Anti-mold filter

Содержание SAP-KCRV243GJ















































































Результаты поиска

Содержание SAP-KCRV243GJ

Отзывы:

Похожие инструкции для SAP-KCRV243GJ

Бренды по названию

Популярные бренды

Sanyo SAP-KCRV243GJ, Техническое и сервисное руководство

Результаты поиска

Содержание SAP-KCRV243GJ

Отзывы:

Похожие инструкции для SAP-KCRV243GJ

Бренды по названию

Популярные бренды