Sanyo SAP-KCRV243GJ Скачать руководство пользователя страница 52

Страница: 52 / 78

Remote Control Unit (Continued)

NOTE

The illustration above pictures the remote control unit after the cover has been lowered

and removed.

When you press the buttons on the remote control unit, the mark appers in the

display to transmit the setting changes to the receiver in the air conditioner.

Transmitter

Sensor

Display

A temperature sensor inside the remote control unit senses the room temperature.

Information on the operating conditions is displayed while the remote control unit is

switched on. If the unit is turned off, only the mode that was set previously is still

displayed.

: When you press this button, the current operation mode is set to the HIGH

POWER mode, and the unit is operated in this mode for 15 minutes.

1 HR.TIMER button

(1-HOUR OFF TIMER)

: When you press this button, regardless of whether the unit is operating or

stopping, the unit operates for one hour and then shuts down.

Press the button to increase the set temperature.

Press the button to reduce the set temperature.

For details, see Automatic operation and Manual operation.

Temperature setting

buttons (TEMP.)

HIGH POWER button

ON / OFF operation button

This button is for turning the air conditioner on and off.

NORMAL

1HR.

AM
PM

1HR.

****

Sensor

AIR CONDITIONER

Transmitter

ON/OFF operation button

HIGH
POWER

ON.I/OFF.O

TEMP.

Temperature setting buttons (TEMP.)

ECONOMY button

MODE selector button

FAN SPEED selector button

FLAP button

A/C SENSOR button

ADDRESS switch
Battery compartment (Pull off the
cover to expose the batteries.)

Model No.: RCS-3MVHPS4E

Display

HIGH POWER button

1 HR. TIMER button

OFF TIME setting button

ON TIME setting button

Return button

Advance button

SET button

CANCEL button

CLOCK button

ACL button

OFF

ECONOMY MODE

FLAP FAN SPEED

SET

CANCEL

CLOCK

BATTERIES

A/C

SENSOR

****

NORMAL

1HR.

AM
PM

1HR.

AIR CONDITIONER

HIGH
POWER

ON.I/OFF.O

TEMP.

(Cover closed)

1HR.

Содержание SAP-KCRV243GJ















































































Результаты поиска

Содержание SAP-KCRV243GJ

Отзывы:

Похожие инструкции для SAP-KCRV243GJ

Бренды по названию

Популярные бренды

Sanyo SAP-KCRV243GJ, Техническое и сервисное руководство

Результаты поиска

Содержание SAP-KCRV243GJ

Отзывы:

Похожие инструкции для SAP-KCRV243GJ

Бренды по названию

Популярные бренды