Sanyo SAP-KCRV243GJ Скачать руководство пользователя страница 50

Страница: 50 / 78

8. Unit Display and Operation Selector

IMPORTANT

Avoid using radio equipment such as mobile phone near

(within 1 m) the remote control receiver. Some radio

equipment may cause malfunction of the unit.

If the trouble happens, disconnect power and restart the

air conditioner after a few minutes.

This section picks up infrared signals from the remote control unit (transmitter).

REMOTE CONTROL

receiver

Operation selector

ON position

OFF position

This position is for operating the air conditioner with the wireless remote control unit.

Set the selector normally in this position.

Switch the selector to the OFF position if you are not going to use the air conditioner

for a new days or longer.

WARNING

CAUTION

The OFF position does not disconnect the power. Use the main power switch

to turn off power completely.

TEST position

This position is used only when servicing the air conditioner.

Do not set at the TEST position for normal operation.

This position is used only when setting address of the remote control unit.

DEMO position

This lamp lights when the system is in the continuous AUTO (red, orange or

green), HEAT (red), DRY (orange) and COOL (green) mode.

OPERATION lamp

This lamp lights when the system is being controlled by the timer.

TIMER lamp

When a fault occurs in the air conditioner, this lamp turns on or flashes in

combination with the other two lamps to indicate the type of fault.

SERVICE Lamp

DEMO.
TEST
ON
OFF

Operation selector

TIMER
lamp

OPERATION
lamp

TIMER OPERATION

INDOOR UNIT

KRV 243
KRV 303

Содержание SAP-KCRV243GJ















































































Результаты поиска

Содержание SAP-KCRV243GJ

Отзывы:

Похожие инструкции для SAP-KCRV243GJ

Бренды по названию

Популярные бренды

Sanyo SAP-KCRV243GJ, Техническое и сервисное руководство

Результаты поиска

Содержание SAP-KCRV243GJ

Отзывы:

Похожие инструкции для SAP-KCRV243GJ

Бренды по названию

Популярные бренды