Sanyo SAP-KCRV243GJ Скачать руководство пользователя страница 70

Страница: 70 / 78

Care and cleaning (continued)

Air intake grille

Arm

Air Cleaning Filter

The air cleaning filter removes dust and dirt from the air, and reduces odors and smoke

from tobacco.

WARNING

This air cleaning filter cannot remove harmful gases or vapors nor ventilate air in

the room. You must open doors or windows frequently when you use gas or oil

heating appliances. Otherwise there is a risk of suffocation in extreme cases.

How to install the air

cleaning filter

The air cleaning filter needs to be installed behind the anti-mold filter.

1. Remove the anti-mold filter.

2. Install the air cleaning filter

in the position shown in the

figure.

3. Reinstall the anti-mold filter.

Air
cleaning
filter

NOTE

In general, the filter should be replaced once every three months.

Dirty air clean filters cannot be washed and reused. Purchase a replacement filter at

your local dealer.

Cleaning the main unit and

remote control unit

Wipe clean using a soft, dry cloth.

To remove stubborn dirt, moisten a cloth in warm water no hotter than 40

, wring

thoroughly, and then wipe.

The air intake grille can be removed in order to wash it with water.

Removing and remounting

the air intake grille

With the air intake grille open all the way, grip both arms with your hands and pull toward

you to remove.

To remount, hold the air intake grille roughly horizontal and push it in until the arm shafts

fit into the indentations in the main unit, then fit the grille into place.

CAUTION

When using a footstool or the like, be careful not to let it tip over.

Washing the grille

with water

Clean the grille gently using a soft sponge, or the like. Then wipe away any remaining

moisture.

Neutral detergent may be used to remove stubborn dirt. Then rinse thoroughly with

water and wipe away any remaining moisture.

Содержание SAP-KCRV243GJ















































































Результаты поиска

Содержание SAP-KCRV243GJ

Отзывы:

Похожие инструкции для SAP-KCRV243GJ

Бренды по названию

Популярные бренды

Sanyo SAP-KCRV243GJ, Техническое и сервисное руководство

Результаты поиска

Содержание SAP-KCRV243GJ

Отзывы:

Похожие инструкции для SAP-KCRV243GJ

Бренды по названию

Популярные бренды