Sanyo SAP-KCRV243GJ Скачать руководство пользователя страница 49

Страница: 49 / 78

7-7. Installation Check Sheet

The strength of the installation location is sufficient

to support the A/C weight.

The indoor and outdoor units are installed level and

vertically.

The power and voltage are as specified.

Inter-unit cables are securely fastened to the termi-

nal board.

Inter-unit cables are securely fixed.

The power cord and inter-unit cables are not con-

nected anywhere along their paths.

The ground wire is securely connected.

An air purge of the refrigerant circuit has been con-

ducted.

A leak test of the tubing connections has been per-

formed.

Thermal insulation has been applied to the tubing

connections.

Drain connections are secure and water drains

properly.

Putty has been used to close the hole in the wall.

All service valves are fully open.

Remote controller signals are being positively

received.

Содержание SAP-KCRV243GJ















































































Результаты поиска

Содержание SAP-KCRV243GJ

Отзывы:

Похожие инструкции для SAP-KCRV243GJ

Бренды по названию

Популярные бренды

Sanyo SAP-KCRV243GJ, Техническое и сервисное руководство

Результаты поиска

Содержание SAP-KCRV243GJ

Отзывы:

Похожие инструкции для SAP-KCRV243GJ

Бренды по названию

Популярные бренды