Santec ECL-210 Скачать руководство пользователя страница 83

Страница: 83 / 96

10-2

ECL-210 Operation Manual

10.3. Cleaning the Optical Connectors

It is important to ensure the optical connector of the ECL-210 remains clean. Any dirt that

accumulates will cause increased loss and when high optical powers are used may lead to connector

damage. Periodic cleaning of the optical connectors is recommended. This is achieved by removing

the connector adapter as indicated in the cleaning procedure below.

1. Remove the two screws holding the connector adapters as shown in the diagram above.

2. Pull the connector adapters forward to remove it from the ECL-210 unit.

3. Carefully clean the surface of the protruding optical connector using a soft lint free cloth

moistened with alcohol. Do not press unnecessarily on the end of the connector as this will

cause it to become detached from its socket.

4. Carefully replace the connector adapter by sliding it over the protruding optical connector and

tighten with the two fixing screws. The alignment notch in the connector adapter should be

positioned at the top of the connector.

OPT.OUT

DANGER!!

This product uses a semiconductor laser. The laser beam may cause injury if it

impinges the eye. Always ensure that the ECL-210 unit is off and no light is being

emitted before cleaning the optical connector.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание ECL-210

































































































Результаты поиска

Содержание ECL-210

Отзывы:

Похожие инструкции для ECL-210

Бренды по названию

Популярные бренды

Santec ECL-210, Руководство по эксплуатации

Результаты поиска

Содержание ECL-210

Отзывы:

Похожие инструкции для ECL-210

Бренды по названию

Популярные бренды