Santec ECL-210 Скачать руководство пользователя страница 76

Страница: 76 / 96

EXTERNAL CAVITY TUNABLE LD LIGHT SOURCE ECL-210

8-5

*This command does not support "echo-back" in RS-232C communication.

Sets output variable to actual LD inject current (mA).

Used with ACC control, sets target LD injection current

(mA).

CU xxx.xx

Sets output variable to target value for LD inject current (mA).

CUT

Sets control mode to ACC mode (ACC on).

Sets control mode to APC mode (ACC off).

Sets output variable to indicate attenuator setting (dB).

Sets attenuator setting to a specific value (dB).

AT xx.xx

Switches automatic attenuator control mode on.

ATE

Switches automatic attenuator control mode off.

ATF

Sets output variable to indicate actual LD temperature (˚C). TL

Sets target value for LD temperature (˚C)

TL xx.xxx

Sets output variable to indicate target LD temperature (˚C). TLT

Sets output variable to indicate actual fine tuning setting.

Sets target value for (target) fine tuning setting.

FI xxx.xx

Sets output variable to indicate target fine tuning setting.

FIT

Switches coherence control function on.

Switches coherence control function off.

Sets output variable to indicate coherence control setting.

Sets coherence control setting to specific value (range 0-10).

CV xx.xx

Initiates reset of MLS rack and ECL-210 units.

Stores all current parameter settings to internal memory.

Sets output variable to indicate status.

SU*

Receive data command for RS-232C communication only.
The value of the output variable that has been set is received
after this command is issued.

DI*

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание ECL-210

































































































Результаты поиска

Содержание ECL-210

Отзывы:

Похожие инструкции для ECL-210

Бренды по названию

Популярные бренды

Santec ECL-210, Руководство по эксплуатации

Результаты поиска

Содержание ECL-210

Отзывы:

Похожие инструкции для ECL-210

Бренды по названию

Популярные бренды