Santec ECL-210 Скачать руководство пользователя страница 89

Страница: 89 / 96

11-4

ECL-210 OPERATION MANUAL

11-4 Rack Mount Angle

This option is to attacch rack mount angles to fix ECL-210 to EIA or JIS standard rack. Ears

for MLS-8100 are different from those for MLS-2100.

11-4-1. MLS-8100

(1) Remove a cover from where rack mount angles will be fixed.
(2) Fix the rack mount angle with screws.
(3) Fix ECL to the rack with screws.

NOTE

MLS-8100 weighs 8kg without the unit. Please be aware of dropping it when attaching

it to the rack.

11-4-2. MLS-2100

11-4-2-1. Rack mount angle (A/B)

(1) Remove a cover from where the rack mount angle will be fixed
(2) Fix the rack mount angle with screws.
(3) Fix ECL to the rack with screws.

11-4-2-2. Rack mount angle (C)

(1) Remove a cover from where the rack mount angle will be fixed
(2) Fix the rack mount angle with screws.
(3) Fix ECL to the rack with screws.

NOTE

MLS-2100 weighs 6kg without the unit. Please be aware of dropping it when attaching

it to the rack.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание ECL-210

































































































Результаты поиска

Содержание ECL-210

Отзывы:

Похожие инструкции для ECL-210

Бренды по названию

Популярные бренды

Santec ECL-210, Руководство по эксплуатации

Результаты поиска

Содержание ECL-210

Отзывы:

Похожие инструкции для ECL-210

Бренды по названию

Популярные бренды