Santec ECL-210 Скачать руководство пользователя страница 27

Страница: 27 / 96

5-4

ECL-210 Operation Manual

(19) SIF (serial interface) connector

This is a connector for RS-232C communication. It is used in numeric key operation or table
operation by external devices such as Zaurus or so. (Please refer to Section 8.2. RS-232C)

(20) Main switch

This is the key switch to change power ON/OFF of the system. To cut off the power source

from the system completely, pulling out the power code is required. The key cannot be pulled

out with power ON.

(21) Protection cover

This is a protective cover to avoid direct output light and to protect the connector from damage

and dust.

(22) Optical output connector

This is the optical output connector from light source unit.

(23) LF modulation input terminal

This is LF modulation input terminal for the control circuit of the light source unit. The driv-

ing current can be controlled for input voltage. The input impedance is 47kÉ

∂

The connector

is SMA.

(24) RF modulation input terminal (Option)

This is RF modulation input terminal for LD of the light source unit. The impedance is ad-

justed by 50É

∂

. The connector is SMA.

(25) Unit LED

This LED indicates the unit movement status. This is lit ON when the power is supplied from

MLS.

(26) DANGER seal

This mark indicates the possibilities of danger by LASER. Do not look into the beam directly.

(27) Inscription panel

The model #, options, and serial # of ECL-210 are mentioned on this.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание ECL-210

































































































Результаты поиска

Содержание ECL-210

Отзывы:

Похожие инструкции для ECL-210

Бренды по названию

Популярные бренды

Santec ECL-210, Руководство по эксплуатации

Результаты поиска

Содержание ECL-210

Отзывы:

Похожие инструкции для ECL-210

Бренды по названию

Популярные бренды